0
5. Install the rear grid (6) on the motor then use grid lock (5) to fasten it.
0
6.
Install the fan blead (4) onto the motor axis (3), then screw it anticlockwise.
0
7.
Install mist spray ring (1) on the front grid (2) by using 3 screws.
0
8. Fix the front grid (2) and rear grid (6) together by using the grid circle (7), and use the circles screw
to fasten it.
0
9. Pull the mist pole (20) onto the mist spray rings (1) snag.
10. According to figure 3 fill the water tank with water. Use ionized water which is not hotter than 40 °C.
11.
Put 2 pieces of AAA sized batteries into the remote control
The device can now be connected to the mains.
CAUTION: RISK OF ELECTRIC SHOCK!
Do not attempt to disassemble of modify the unit or its accessories. In case any part is damaged,
immediately power off the unit and seek the assistance of a specialist.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
FEATURES
Humidifier fan with extra functions
•
color touch panel
•
every function can be remote controlled
•
adjustable fan and humidifier, 3 stages
•
natural wind and night mode
•
oscillation (75°)
•
12 hour fan shut down time
•
aroma storage compartment
•
functions switchable
independently from the fan: humidifier, ionizer, heated compartment for the mosquito mat
FIGURE
1
:
1.
mist spray ring
•
2.
front grid
•
3.
blade lock
•
4.
blades
•
5.
grid lock
•
6.
rear grid
•
7.
grid circle
•
8.
motor axis
•
9.
motor
•
10.
axis for head
tilting
•
11.
metal support pole
•
12.
connection terminal
•
13.
handle screw
•
14.
touch control panel
•
15.
body
•
16.
water tank
•
17.
base
18.
wheels
•
19.
base lock
•
20.
mist pole
•
21.
remote control
FIGURE 2.
22
.
heated compartment for mosquito repeller mat
•
2
3
.
aroma storage compartment
•
24
.
freezer pack
•
25
.
Water drain screw
•
26
.
remote control holder compartment
DEVICE FEATURES, AND USAGE
Connect the device to a standard 230 V~ / 50 Hz mains connection socket.
The device now emits a short beeping sound.
After pressing the ON/OFF button once the
humidification
function (3 stages), the
ionization
and the
insect repeller
function can be
selected. If these functions are chosen the fan function cannot be activated.
By pressing the ON/OFF button a second time the fan starts at the lowest stage, and the display show the premises temperature. Beside
the 3 previously mentioned functions the
timer,
oscillation
and
wind
functions can also be selected.
With the
SPEED
button the fans speed can be selected. The lowest stage is marked with green, the middle with orange, and the fastest
with red bars on the display.
With the
TIMER
button we can choose a timeframe of 1-12 hour after which the device shuts down. The room's temperature and the
remaining time is shown interchangeably in 5 sec intervals. The display of the TIMER is shown in hours.
The
ION
button turns on the ionization function.
With the
MODE
button the natural wind mode can be chosen, which is signaled by a pine tree on the display, or the night mode which is
signaled by a moon.
The
MOSQUITO
button switches on the heating compartment (22) located on the backside of the device, in which only commercially
distributed insect repellent mat can be placed. The size of the mat can be maximum 22x2x35 mm. If turned on a red spiral is displayed on
the display. Only replace the mat after 5 minutes from turning the function off (the mat can be hot)!
The
OSC
button switches the right-left oscillating movement on or off.
The
MIST
button starts the ultrasonic cold humidification. The intensity can be set in three stages. If turned on a green mist clouds can be
seen on the display, and the vertical line on the front of the device gets a blue backlighting. Red backlight indicates that there is no more
water in the water tank, at the same time the function turns off.
