11
Telis 6 Chronis RTS
Copyright © 2010 - 2016 Somfy SAS. All rights reserved.
EN
7.2.3. Simulated presence function
In automatic mode, the "Simulated presence" function randomly changes the times at which the
programmed automatic orders are triggered, within a range of 0 to 30 minutes. This function is
specially recommended to simulate your presence when you are away from home for an extended
period of time.
7RDFWLYDWHWKHIXQFWLRQ
1)
0DNHVXUHWKDWWKH7HOLV&KURQLV576LVLQDXWRPDWLFPRGHLILWLVLQPDQXDOPRGHEULHÀ\SUHVV
the selection button (
) to switch to automatic mode).
2)
Press
both arrow
buttons
(
and
)
simultaneously
:
the (
) symbol appears on the screen: the "Simulated
presence" function is activated.
7RGHDFWLYDWHWKHIXQFWLRQ
-
Press
both arrow buttons
(
and
)
simultaneously
: the
(
) symbol disappears from the screen: the "Simulated
presence" function is deactivated.
-
Or
switch to manual mode.
Switching to manual mode automatically deactivates the "Simulated presence" function. The
function must be reactivated, if required, when returning to automatic mode.
7.2.4. Modifying the general parameters of the remote control transmitter
7KH JHQHUDO SDUDPHWHUV RI WKH UHPRWH FRQWURO WUDQVPLWWHU FDQ RQO\ EH PRGL¿HG LQ DXWRPDWLF
mode.
1)
0DNHVXUHWKDWWKH7HOLV&KURQLV576LVLQDXWRPDWLFPRGHLILWLVLQPDQXDOPRGHEULHÀ\SUHVV
the selection button (
) to switch to automatic mode).
2) Press and
hold
the selection button (f)
until
6(7 DQG <($5 DSSHDU RQ WKH VFUHHQ !V
5HPRWHFRQWUROVHWWLQJVPRGHLVDFWLYDWHG7KH\HDUÀDVKHVWKLVLVWKH¿UVWSDUDPHWHUWREHVHW
3) Follow the procedure in the "
Setting the general parameters of the remote control transmitter
"
section.
4)
2QFHWKHODVWSDUDPHWHUKDVEHHQFRQ¿UPHG5HPRWHFRQWUROVHWWLQJVPRGHLVGHDFWLYDWHGDQG
the Telis 6 Chronis RTS returns to automatic mode.
"Remote control settings" mode can be deactivated at any time by pressing and holding the
VHOHFWLRQEXWWRQI2QO\FRQ¿UPHGSDUDPHWHUVDUHVDYHG
8. Tips and recommendations
Questions about the Telis 6 Chronis RTS?
2EVHUYDWLRQV
Possible causes
Solutions
The end-products on the
selected channel do not
react at all when a button
on the Telis 6 Chronis
RTS is pressed.
The batteries are low.
Replace the batteries.
The end-product(s) is(are) not on
the selected channel.
Select the corresponding channel or add the
motor or receiver to the channel.
The remote control transmitter is
not programmed.
See the "
Adding/Deleting a telis 6 Chronis RTS
"
section.
External radio equipment is
interfering with the radio reception.
Turn off any radio appliances nearby.
The remote control transmitter is in
automatic mode.
%ULHÀ\SUHVVWKHVHOHFWLRQEXWWRQWRVZLWFKWR
manual mode.
The motor(s) or receiver(s) are in
thermal cut-out mode.
Wait for the motor to cool down, then press the
desired button again.
5065945B_Chronis_6_RTS print.pdf 61
7/16/2020 9:50:02 AM
5065945B_Chronis_6_RTS print ok.pdf 61
7/16/2020 9:52:40 AM
Summary of Contents for Telis 6 Chronis RTS
