background image

37

Copyright © 2005 - 2014 Somfy SAS. All rights reserved.

EN

Non contractual images

2. 4. TIPS AND ADVICE ON INSTALLATION

2. 4. 1. Questions about the Orea WT?

Problems

Possible causes

Solutions

The awning 
rotates in the 
wrong direction.

The wiring is incorrect.

Check the wiring and modify as required.

The awning does 
not operate.

The wiring is incorrect.

Check the wiring and modify as required.

The overheating protection on 
the drive has been activated.

Wait for the drive to cool down.

The control point is  
not compatible.

Check the compatibility and replace the 
control point as required.

The awning stops 
too soon.

The awning is encountering 
friction when it moves: rubbing 
on the guide rails and cassette, 
interference between the 
winding tube and the drive, etc.

Check the installation of the awning and 
adjust any rubbing points.
_ {   {
   

The drive has been installed in 
a new awning.

Restore the drive to its original 
   
¡  { ¡

The awning does 
not stop at the 
lower end limit.

£{ 
are unsuitable.

Check that the awning is secured to the 
winding tube with rigid links.

The awning does 
not stop at the 
upper end limit.

The system for stopping the 
awning in the upper position  
is unsuitable.

}{ {  {   {
   {
removable stops incorporated into the 
guide rails or an end slat that acts as  
a stop.

2. 4. 2. Re-setting the end limits

1

 Use universal adjusting cable 9015971 (follow the instructions in the corresponding 
manual for connection), or use a non-locking double push-button switch.

Re-setting the lower end limit

_ { {   {   {   {
reaction by the end product.

1) 

Place the awning at its lower end limit.

2) 

) {¡ƒ¡   G

3) 

Wait for 2 seconds.

4) 

Press the "Down" button until the awning moves back 
and forth.

5) 

Repeat steps 3 and 4 four times.

+

The last back and forth movement is brief.

6) 

Place the awning in the desired lower end limit 
position.

7) 

š {¡]¡  

_ {   €

8) 

Wait for 2 seconds.

9) 

Press the "Up" button until the awning moves back 
and forth.

 

|

The new lower end limit position is programmed.

2)

3)

5)

7)

9)

1)

4)

6)

8)

0.5 s

5 s

[Step 3 

+

Step 4]

x 4

2 s

2 s

Summary of Contents for Orea 50 WT









Reviews: