![background image](http://html1.mh-extra.com/html/somfy/heating-modulis-5061611a/heating-modulis-5061611a_installation-manual_1318029042.webp)
Copyright © 2008 Somfy SAS. All rights reserved.
Heating Modulis RTS Ramp
24
Installation guide
EN
Problems
Possible causes
Solutions
The Heating Modulis RTS
Ramp does not heat up
suffi ciently. (next)
The capacity of the Heating Modulis RTS
Ramp is not suffi cient.
See the heated surface in the technical data.
The Heating Modulis RTS
Ramp does not switch on.
The correct fuse has not been fi tted to the
equipment.
Check the rating of the fuse. To operate the ramp
correctly, a 16 A delay fuse is required.
One or more heating lamps is blown or
broken.
Replace the heating lamp(s).
The heating lamp(s) linked to the Heating
Modulis RTS Ramp exceed 2000 W.
Ensure that the heating lamp(s) linked to the
Heating Modulis RTS Ramp do not exceed 2000
W in total.
Caution! This reset removes all control points but retains the favourite
heat level programmed.
Caution! Only switch off the power to the Heating Modulis RTS Ramp
to be reset!
CAUTION! Do not use an Inis RT/Inis RTS control point for resetting
1) Cut the power supply for 2 seconds.
Switch the power supply back on for approximately 10 seconds (for
2)
at least 5 seconds but no longer than 15 seconds).
Cut the power supply for 2 seconds.
3)
Switch the power supply back on: the heating lamp fl ashes slowly.
4)
Briefl y press the PROG button on the new RTS control point (f):
5)
The heating lamp will come on then go out again to indicate that
-
the new RTS control point has been programmed into the Heating
Modulis RTS Ramp.
2 seconds.
2 seconds.
10 seconds.
2
OFF
OFF
3
4
ON
ON
…
a
f
5
PROG.
f
1
8.2 Replacing a lost or broken control point
Caution: This reset is carried out if all the RTS control points have been lost or broken.
8.3 Restoring the original confi guration
Caution! This reset removes all control points and resets the favourite heating level to 33% of the
total power.
Caution! Only switch off the power to the Heating Modulis RTS Ramp
to be reset!
Caution! Do not use the Inis RT/Inis RTS control point for resetting!
1) Cut the power supply for 2 seconds.
Switch the power supply back on for approximately 10 seconds (for
2)
at least 5 seconds but no longer than 15 seconds).
Cut the power supply for 2 seconds.
3)
Switch the power supply back on: the heating lamp fl ashes slowly.
4)
Press the PROG button on the RTS control point until the heating
5)
lamp comes on then goes out twice in succession: all control points
have been removed.
Follow the procedures in the section entitled “Commissioning” to
-
add RTS control points.
9. Technical data
Radio frequency
433.42 MHz
Number of programmable RTS
control points
12 maximum
Power supply
230 V ~ 50 Hz
Dimensions (mm)
483 x 176 x 230
Maximum total power
2000 W
Weight (kg)
3.5
Index protection rating
IP24
Heating lamp
Philips® HeLeN
Operating temperature
- 20°C to + 60°C
Service life (hours)
5000
Safety level
Category II
Heating surface (m
2
)
16
2 seconds.
2 seconds.
10 seconds.
b
1
2
OFF
OFF
3
4
5
ON
ON
PROG.
…
5061611X02_HMR_Ramp_RTS.indb 24
25/05/09 18:41:06