manualshive.com logo in svg

Soma Networks SOMAport R3.0, Setup Manual, Page: 7 / 58

Share
Download
Soma Networks SOMAport R3.0 Setup Manual Download Page 7

7

R

EGULATORY

 N

OTICES

The SOMAport has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, you can try to correct 
the interference by:

„

Relocating the SOMAport

„

Increasing the distance between the SOMAport and the device 
experiencing the interference

„

Connecting the equipment to an outlet on a circuit different from 
that to which the SOMAport is connected

 

 

ATTENTION: 

Changes or modifications not expressly approved by SOMA

Networks for compliance could void the user's authority to operate the
equipment.

Declaration of Conformity

SOMA Networks, Inc.,

185 Berry Street, Suite 

46

00

San Francisco, CA 94107 U.S.A.

(415) 882-6500

declares under our sole responsibility that the product

SOMAport

complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

sp3.book  Page 7  Thursday, July 22, 2004  3:21 PM

Summary of Contents for SOMAport R3.0



























































Reviews:

No comments