Sollae CSE-M53N User Manual Download Page 62

Page: 62 / 72

CSE-M53N User Manual Ver. 2.5

Sollae Systems Co., Ltd.

- 61 -

http://www.ezTCP.com

8.4

Factory Reset

It is a function physically initializes all the setting. You can save a setting to user-defined

ENV region and use it as default values by the factory reset. However, if you do not use the
region, Factory Reset uses a factory default by manufacturer as its default values.



Using Factory Reset

①

Connect pin #ISP to GND (input LOW signal).

②

Connect pin #ISP to GND (input LOW signal over 10 seconds).

③

Factory Reset will be automatically implemented to default values.

④

Disconnect the two pins from GND.

⑤

Reboot.



Setting custom default values

①

Change the mode to Serial Configuration mode

②

Save custom default values by ezManager or serial configuration commands

③

Input the command below

<SPACE>

3c5a

<CR>

④

After step ③, current values in the SRAM is saved in user-defined ENV region
and the values will be always used for Factory Reset.

Summary of Contents for CSE-M53N









































































Search results

Summary of Contents for CSE-M53N

Reviews:

Related manuals for CSE-M53N

Brands by name

Popular brands

Sollae CSE-M53N, User Manual

Search results

Summary of Contents for CSE-M53N

Reviews:

Related manuals for CSE-M53N

Brands by name

Popular brands