background image

Upgrade

User can update the inverter system through a U-disk.

2)  Make sure the DC switch is off and the AC is disconnected with grid. 
Unscrew the waterproof lid of Upgrade port by straight screwdriver as 

1)  Please contact our service support to get the update file, and extract 
it into your U-disk as the following file path:  

Make sure the directory is in accordance with above form strictly! 
Do not modify the program file name ! Or it may cause the inverter 
not work anymore !

Make sure the input voltage is more than 121V (in good illumination 
condition), or it may result in failing during updating.

“update\

\618.00117.00_X1_8K_

_Vx.xx_xxxxxxxx.usb”;

ARM

ARM

Upgrade 

Update

ARM
DSP

3)  then insert U-disk into the USB port on the bottom of the inverter. 
Then turn on DC switch or connect the PV connector, the LCD will show 
picture as below. 

During updating, please don’t turn off the DC switch or 
disconnect the PV connector, then reinsert the U-disk if 
the updating is stopped.

The earth fault alarm is the additional detection, as required by AS 
4777.2 and AS/NZS 5033, it will give an alarm once the earth 
impedance of the PV arrays is less than 

30KΩ

 .

Earth Fault Alarm(Optional)

26

27

Installation 

Installation 

5)  After the upgrade is complete, please remember to turn off the DC 
switch or disconnect the PV connector, then pull off the U-disk, screw 
the waterproof lid.

Note: Vx.xx is version number, xxxxxxxx is file completion date.

4)  Press up and down to select the one that you want to update and 
press “OK” to confirm to update.  

U-disk

5 m

m

Straight screwdriver

Waterproof lid

torque:1.5

±

0.2Nm

Ø

4

ARM:

DSP:
“update\DSP\618.00119.00_X1_8K_SLAVE_Vx.xx_xxxxxxxx.usb”;
“update\DSP\618.00118.00_X1_8K_MASTER_Vx.xx_xxxxxxxx.usb”.

Warning!

Warning!

Warning!

5.6  Run the inverter

a. Check that device is  xed well on the wall.

b. Make sure all the DC breakers and AC breakers are disconnected.
c. AC cable is connected to grid correctly.
d. All PV panels are connected to inverter correctly, DC connectors which 
are not used should be sealed by cover.
e. Turn on the external AC and DC connectors.
f.  Turn on the DC switch to the “ON”position.

Start inverter after checking all below steps:

Ø

Summary of Contents for X1-6.0-T-D

























Reviews: