background image

 

W W W . S O L A R P O W E R . N E T . A U

 

Page 19 of 20 

Revision: 9h Issued: 01 August 2008 

 
 

SolarPower Pipe Layout Drawing 

 

 

1.

 

The  warranty  only  applies  where  the  SYSTEM  has  been  installed  and  commissioned  according  to 

SOLARPOWER installation instructions and by an authorised SOLAPOWER installer or licensed plumber.          

 

2.

 

Free  repair  or  replacement  is  provided  within  the  metropolitan  area  of  Australian  capital  cities  as  defined  by 

SOLARPOWER within 30km of the city centre or a branch, office or accredited service agent. In other areas 
defective parts or SYSTEMS must be returned to the point of sale before replacement can be considered under 
the  terms  of  the  warranty.    Freight  and  insurance  charges  for  the  transport  of  a  defective  and  replacement 
SYSTEM or parts are payable by the owner.   

 

3.

 

Where a failed component or SYSTEM is replaced under warranty, the balance of the original warranty period 

shall remain effective.  The replaced part or SYSTEM does not carry a new warranty. 

 
4.

 

The warranty only applies to the SYSTEM and does not cover any plumbing or electrical parts.  The electrical 

element, the circulator pump and pump controller have a 12-month replacement warranty. 

   

5.

 

Warranty  claims  must  include  all  details  listed  overleaf  and  should  be  made  to  the  point  of  sale  or  to  the 

company address listed below within one (1) month of the appearance of the defect.  

 

6.

 

This warranty does not cover the SYSTEM where it is found that the SYSTEM does not suffer a defect; where 

the  complaint  is  related  to  solid  matter  lodging  under  valve  seats;  where  there  is  a  failure  of  water  supplies, 
electrical supplies or the result of extreme water pressure or thermal input. 

 

7.

 

This warranty does not cover the SYSTEM where the SYSTEM is located in a position that does not comply 
with either the SolarPower installation instructions or the relevant statutory requirements and as a consequence 
there is a need for major dismantling or removal of doors, walls etc, or the use of special equipment to bring the 
SYSTEM to ground level. 

 

8.

 

This  Warranty  excludes  the  removal  of  scale  formation  in  the  waterways  where  the  SYSTEM  has  been 

connected to a harsh water supply. 

 

9.

 

Subject  to  any  statutory  provisions  to  the  contrary,  this  warranty  excludes  claims  for  damage  to  furniture, 

carpets, walls, foundations, or any other consequential loss either directly or indirectly due to leakage from the 
SYSTEM. 

 

10.

 

The  collector  glass  cover-plate  is  not  covered  by  this  Warranty.    Your  household  insurance  policy  should  be 

extended to include breakage of the collector cover-plate glass. 

 

11.

 

This warranty excludes damage resulting from acts of God, fire, lightning, flood, earthquake, landslide, storm, 

hail, frost, wind or other adverse weather conditions 

 

12.

 

The warranty excludes damage resulting from misuse, faulty installation or repairs carried out by persons other 

than a SOLARPOWER accredited service agent or technician. 

 

13.

 

Water  Quality,  must  meet  the  detailed  description  of  the  requirements  for  water  quality  as  listed  in  the 

installation manual. 

Summary of Contents for SP4002





















Reviews: