Solaronics SSTG Installation, Operation & Maintenance Instructions Manual Download Page 1

Form SST-IOM-14

900040

STAINLESS

SSTG/U

STAINLESS STEEL

GAS-FIRED LOW-INTENSITY INFRA-RED

RADIANT TUBE HEATERS

FOR EITHER INDOOR OR OUTDOOR INSTALLATION

INSTALLATION, OPERATION, &

MAINTENANCE INSTRUCTIONS

SSTG

 (Straight Tube)

SSTU

 (U-Tube)

! WARNING !

Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this
equipment.

FOR YOUR SAFETY

 

If you smell gas: open windows; don’t touch electrical switches, extinguish any open flames; evacuate the
structure; call your gas supplier immediately.

WARNING – NOT FOR RESIDENTIAL USE

 

Failure to comply with instructions could result in unsafe operation, property damage, personal injury, and/or
death.  A gas-fired appliance could expose you to substances in fuel or from fuel combustion, which have
been determined by the State of California to cause cancer, birth defects or other reproductive harm.  For
industrial or commercial use only.

 

Retain these instructions for future reference.  Contact factory for further information.

IMPORTANT

 

Have a qualified electrician check the electrical supply circuit and wall receptacle are properly grounded and
the electrical supply polarity is correct.  The heater control is polarity sensitive and 

will not operate

 properly if

the electrical supply is not wired correctly.

HAZARD INTENSITY LEVELS

 

DANGER

:  Failure to comply will result in severe personal injury or death and property damage.

 

WARNING

:  Failure to comply could result in severe personal injury or death and/or property damage.

 

CAUTION

:  Failure to comply could result in minor personal injury and/or property damage.

Summary of Contents for SSTG





























Reviews: