background image

Configuration with Inverters with SetApp 

Required inverter Firmware CPU version : v4.7xx and later.

To associate the Smart Energy device with the inverter using SetApp:

 1.  Access SetApp as described in the

  Inverter Installation Guide.

 2.  Select 

Commissioning > Communication > ZigBee > Protocol > Home Automation

.

 3.  Return to the 

Commissioning

 screen.

 4.  Select 

Device Manager

. The 

Smart Energy Manager

 screen is displayed.

 5.  Select 

Add Devices

 to start device association with the inverter. A 3 minute 

countdown starts.

 6.  Within the 3-minute time, press and hold the association button for 2 seconds.

SetApp indicates that the device has been associated.

 7.  After all required devices have been associated, tap 

Stop

 in the Smart Energy 

Manager to exit.

To configure the Smart Energy device:

 1.  Go to the monitoring platform web-site on your computer, or open the monitoring 

platform application on your mobile device.

 2.  Click/tap the 

Smart Energy

 icon.

 3.  Select a device and go to 

Details and Settings

.

 4.  Complete the following information:

Rated power

Min active time

Device icon

Device name

 5.  Return to the device screen and configure:

Schedules

Ready-by timers

Excess Solar Power mode (requires a SolarEdge Energy Meter)

Device state

Smart Energy Relay Installation Guide

16

   Configuration with Inverters with SetApp

Summary of Contents for Smart Energy Relay
























Reviews: