background image

IMPORTANT SAFETY INSTRUCTIONS / 
CONSIGNES DE SÉCURITÉ IMPORTANTES

SAVE THESE INSTRUCTIONS / CONSERVEZ CES INSTRUCTIONS

Warning!

To reduce the risk of injury, read all instructions in this document.

 

AVERTISSEMENT!

 

Pour réduire le risque de blessure, lisez toutes les instructions de ce document.

WARNING!

Using this equipment in a manner not specified by SolarEdge in this document  
may impair the protection provided by this equipment. 

WARNING!

The inverter cover must be opened only after switching the inverter ON/OFF/P 
switch located at the bottom of the inverter to OFF. This disables the DC voltage 
inside the inverter. Wait five minutes before opening the cover. Otherwise, there 
is a risk of electric shock from energy stored in the capacitors. 

 

AVERTISSEMENT!

 

Ne pas ouvrir le couvercle de l'onduleur avant d'avoir coupé l'interrupteur situé 
en dessous de l'onduleur. Cela supprime les tensions CC et CA de l'onduleur. 
Attendre cinq minutes avant d’ouvrir le couvercle. Sinon, il y a un risque de 
choc électrique provenant de l'énergie stockée dans le condensateur.

 

WARNING!

Before operating the inverter, ensure that the inverter is grounded properly. This 
product must be connected to a grounded, metal, permanent wiring system, or 
an equipment-grounding conductor must be run with the circuit conductors 
and connected to the equipment grounding terminal or lead on the product.

 

AVERTISSEMENT!

 

Avant d'utiliser l'onduleur monophasé, assurez-vous que l'onduleur est 
correctement mis à la terre. Ce produit doit être raccordé à un système de 
câblage fixe, métallique, l'équipement-le conducteur de mise à la terre doit être 
exécuté avec les conducteurs de circuit et raccordé à l'équipement borne de 
mise à la terre ou de plomb sur le produit.

WARNING!

Opening the inverter and repairing or testing under power must be performed 
only by qualified service personnel familiar with this inverter. 

IMPORTANT SAFETY INSTRUCTIONS / CONSIGNES DE SÉCURITÉ

IMPORTANTES     

7

Three Phase Inverter with Synergy Technology P/N: SExxK-xxxxIxxxx SExxK-xxxxIxxxx

Summary of Contents for SEK-I Series





























































































Reviews: