SOLARACK SR-COMP Installation Manual Download Page 8

Recommended  Placement  &  Spacing  of  Roof  Attachments

Page 7

www.solarackusa.com

1st course

2nd course

3rd course

4th course

48”

72”

IMPORTANT:

Flashing should not overhang a 
downslope shingle or a gap in 
shingle material.

- Roof Rafter

- 9” x 12”
  Compositon

Mounting Instructions: Portrait

Mounting Instructions: Landscape

Please follow this instruction graphic when solar modules
are mounted in portrait alignment. Rail must be mounted 
8”-18” from the top and bottom edge of the solar module.

Some  solar  module  manufacturers  may  have  specific 
requirements  rail  placement  that  differs  from  these
instructions, please check with your module manufacture
for compliance regarding mounting requirements. 

Rail must not exceed 24” cantilever 
past the last attachment. (for 6’ span)

Please  follow  this  instruction  graphic  when  solar  modules
are mounted in landscape alignment. Rail must be mounted 
4”-7”  from  the  top  and  bottom  edge  of  the  solar  module.

Some  solar  module  manufacturers  may  have  specific 
requirements  rail  placement  that  differs  from  these
instructions, please check with your module manufacture
for compliance regarding mounting requirements. 

Rail must not exceed 24” cantilever 
past the last attachment. (for 6’ span)

The  SolaRack®  Comp  Kit  is  optimally  spaced  based  on  local  city  code  and  the  rail  system  used. 
For  measurements  related  to  clearances  and  roof  setbacks,  please  refer  to  your  local  building  and  safety  office  or  other 
authorities  having  jurisdiction.  When  using  the  Comp  Kit  with  SolaRack®  Rails,  attachments  may  be  spaced 
up  to  72”.  For  proper  installation,  please  refer  to  the 

detailed  installation  guide  on  page  11. 

Lag  screw  must  be 

installed in the center of a roof rafter and sealant must be applied under the flashing during installation. Installation must be
preformed  by  licensed  professionals  to  avoid  roof  damage.  Removing  stone  gravels  and  deforming  shingles  in  any  way 
during installation can and will shorten the lifespan of the roofing. Be sure not to install systems on poor quality or damaged 
surfaces.   

© 2018 SOLARACK INC. VR2.1                                       

Summary of Contents for SR-COMP


























Reviews: