background image

CONNECTIONS – PLUMBING 

32 

LEFT AND RIGHT HAND SIDE WATER CONNECTIONS 

A kit is supplied with an E6X series water heater to plug or cap off the unused cold water and hot water fittings. 
 
The kit contains: 
 

2 x ¾” brass plugs 

2 x plastic caps 

2 x insulation rubber discs, pre-fitted into plastic caps 

 

Plugging or Capping Off Unused Connections 

 

Apply approved sealing tape or compound to the thread of 
each plug. 

 

Fit the 

¾” plugs to the unused cold water fitting and unused 

hot  water  fitting.  Tighten  the  plugs 

using  a  3/8” square 

driver. 

 

Fit  a  plastic  cap  with  its  insulation  rubber  disc  over  each 
plug. 

 

TEMPERATURE PRESSURE RELIEF VALVE 

The temperature pressure relief valve is shipped in a plastic bag attached to the water heater. The temperature 
pressure relief valve must be fitted before the water heater is operated. Before fitting the  relief valve, make 
sure the probe has not been bent. 
 
To fit the relief valve: 

 

Seal the thread with an approved thread sealant such as Teflon tape - never hemp. Make sure tape does 
not hang over the end of the thread. 

 

Hand  tighten 

the  valve  into  the  opening  marked  “Relief  Valve”  (refer  to  the 

installation  diagram

  on 

page 28)

 

Using a spanner engaged on the valve’s spanner flats and applying medium pressure to tighten, turn the 
relief valve an additional ½ to 1 ½ turns to secure and make the joint water tight, leaving the valve drain 
pointing downwards. 

 

Warning:

 Do not use a pipe wrench or poor fitting tool on the valve body nor over tighten the valve, 

as this could damage the valve and prevent safe operation. 

 

Operate  the  easing  lever  on  the  valve  to  check  the  smooth  operation  of  the  valve  plunger.  It  is  very 
important the lever is raised and lowered gently. The lever should move smoothly and without undue force. 

 

If the lever cannot be moved or is jerky in its movement, then the valve has been damaged and must be 
replaced. 

 

A copper drain line must be fitted to the temperature pressure relief valve (refer to 

"Relief Valve Drain"

 on 

page 33). 

 

The valve must be insulated with closed cell polymer insulation or similar (minimum thickness 9 mm) and 
the insulation installed so as not to impede the operation of the valve. 

The insulation must be weatherproof and UV resistant if exposed. 

 
 

 

 

E6X Models 

Summary of Contents for 250E5X









































Reviews: