manualshive.com logo in svg

Sol GreenWay GRNWY-125, Installation And Owner'S Manual

Share
Download
Sol GreenWay GRNWY-125 Installation And Owner'S Manual Download Page 10

 10   GreenWay™ installation & operation manual                         0410 MKTG-IM-GREEN-002

Solar Light System Test

Once all of the wires have been clicked together and the batteries are installed, perform a diagnostic test.

Press the “PUSH TO TEST” Button.  This will indicate to the CPU to turn on the LED Luminaire(s) and 
operate the lights at full intensity for 5 minutes.  Several diagnostic LEDs will turn on & remain on for several 
seconds.  This is normal.

FIGURE 15

  

aiSUN™ SYSTEM TEST 

Troubleshooting and Diagnostic LEDs

If the LED Luminaire turns on to full brightness, system operates OK and will automatically turn on & off with 
sunset and sunrise. 
If the LED Luminaire does not turn on as described, follow the Diagnostic LED table (below) to troubleshoot 
the system. 
If LED Luminaire does not turn on AND no Diagnostic LEDs are on, aiSUN™ is not powered, check battery 
and fuse connections.

FIGURE 16

  

aiSUN™ TROUBLESHOOTING 

Summary of Contents for GreenWay GRNWY-125


















Reviews:

No comments

Brands by name

Popular brands

Load more brands