Soho SOHO RAID SR2000 User Manual Download

Page: 4 / 32

1-2 Product Specifications

System Specifications

Host Interface

Ultra ATA

RAID level

Installation Space

2 x 5-1/4” Expansion Bay

HDD Interface

EIDE

HDD Selection Mode

Master/Slave

Overheating prevention

6cm Ball Bearing Fan

Environmental Conditions

Operating Temperature

℃

~55

℃

Non operating Temperature

-20

℃

~70

℃

Power

Input Voltage (DC)

+5V, +12V

Reliability

MTBF

＞

250,000 Hours

Dimensions

Measures (mm)

146(W)X238(D)X85(H)

Weight

1.5 Kg(HDD excluded)

Safety

CE Certificate

1-3

System Requirements and support

Hardware Requirements

1. Intel based IBM compatible PC (Pentium III, Pentium

II, Pentium MMX/Pentium, or 100% compatible).

2. HDD with standard EIDE/IDE Interface.
3. 2 x 5-1/4” Expansion Bay.
4. One 4-pin DC power socket outlet.
5. Supports all I/O chips, except ITE IT8680F-A I/O chip.

SOHO RAID

Summary of Contents for SOHO RAID SR2000

































Search results

Summary of Contents for SOHO RAID SR2000

Reviews:

Related manuals for SOHO RAID SR2000

Brands by name

Popular brands

Soho SOHO RAID SR2000, User Manual

Search results

Summary of Contents for SOHO RAID SR2000

Reviews:

Related manuals for SOHO RAID SR2000

Brands by name

Popular brands