background image

3

•  Maintain for safety and longevity – 

Check for 

misalignment or binding of moving parts, breakage of 

parts and any other conditions that may affect the unit’s 

operation. If damaged, repair or replace the damaged part 

before use. Use only original replacement parts designed 

specifically for your model. When replacing any parts, 

you must strictly observe the instructions and procedures 

described in this manual. Special care should be paid to 

any rubber parts, since these parts may increase the engine 

load and decrease its mechanical power if damaged. 

  Always check that all bolts, nuts and knobs are tight before 

using the snow thrower!

m

WARNING!

 Some dust and debris created by the use 

of the tool could contain chemicals known to the State 

of California to cause cancer and birth defects or other 

reproductive harm. Some examples of these chemicals are:

•  Chemicals in fertilizers
•  Compounds in insecticides, herbicides, and pesticides
•  Arsenic and chromium from chemically treated lumber

Your risk from exposure to these chemicals varies, and 

depends on how often you do this type of work. To reduce 

your exposure, work in a well-ventilated area and with 

approved safety equipment, such as dust masks that are 

specially designed to filter out microscopic particles.

Summary of Contents for SJM988

















Reviews: