background image

2

 iii) 

Repair any damage before restarting and operating  

the snow blower.

B Charger  

Safety Instructions

We pay a great deal of attention to the design of every battery 

pack to ensure that we supply you with batteries that are safe, 

durable and have a high energy density. The battery cells have 

a wide range of safety devices. Each individual cell is initially 

formatted and its electrical characteristic curves are recorded. 

This data is then used exclusively to be able to assemble the 

best possible battery packs.

Despite all the safety precautions, caution must always be 

exercised when handling batteries. The following points must 

be obeyed at all times to ensure safe use. Safe use can only 

be guaranteed if undamaged cells are used. Incorrect handling 

of the battery pack can cause cell damage.

IMPORTANT!

 Analyses confirm that incorrect use and poor 

care of high-performance batteries are the main factors 

responsible for personal and/or product damage.

m

WARNING!

 

Use only approved replacement batteries; 

other batteries may damage the cordless snow blower and 

cause it to malfunction, which can lead to serious personal 

injury.

m

CAUTION!

 To reduce the risk of injury, charge the 

EcoSharp

®

 PRO iBAT40XRP lithium-ion battery packs only 

in its designated lithium-ion charger, the iCHRG40-DPC 

or iCHRG40. Other types of chargers present risk of fire, 

personal injury and damage. Do not wire a battery pack to a 

power supply plug or car cigarette lighter. Such misuse will 

permanently disable or damage the battery pack.

• 

Avoid dangerous environments –

 Do not charge the 

battery pack in rain, snow or in damp or wet locations. 

Do not use the battery pack or charger in the presence of 

explosive atmospheres (gaseous fumes, dust or flammable 

materials) because sparks may be generated when inserting 

or removing the battery pack, which could lead to a fire.

• 

Charge in a well-ventilated area – 

Do not block the 

charger vents. Keep them clear to allow for proper 

ventilation. Do not allow smoking or open flames near a 

charging battery pack. Vented gases may explode.

 

NOTE:

 The safe temperature range for the battery is -4°F 

(-20°C) to 113°F (45°C). Do not charge the battery outside 

in freezing weather; charge it at room temperature. 

• 

Maintain charger cord –

 When unplugging the charger, pull 

the plug, not the cord, from the receptacle to reduce the 

risk of damage to the electrical plug and cord. Never carry 

the charger by its cord or yank it by the cord to disconnect 

it from the receptacle. Keep the cord away from heat, oil 

and sharp edges. Make sure the cord will not be stepped 

on, tripped over or subjected to damage or stress when the 

charger is in use. Do not use the charger with a damaged 

cord or plug. Replace a damaged charger immediately.

• 

Do not use an extension cord unless it is absolutely 

necessary – 

Using the wrong, damaged or improperly 

wired extension cord poses a risk of fire and electric shock. 

If an extension cord must be used, plug the charger into a 

properly wired 16 gauge or larger extension cord with the 

female plug matching the male plug on the charger. Make 

sure that the extension cord is in good electrical condition.

• 

Charger iCHRG40 or iCHRG40-DPC is rated for 120 volt 

AC only –

 The charger must be plugged into an appropriate 

receptacle.

• 

Use only recommended attachments –

 Use of an 

attachment not recommended or sold by the battery 

charger or battery pack manufacturer may result in risk of 

fire, electric shock or personal injury.

• 

Unplug charger when not in use –

 Make sure to remove 

battery packs from unplugged chargers.

m

WARNING! 

To reduce the risk of electric shock, 

always unplug the charger before performing any cleaning 

or maintenance. Do not allow water to flow into the charger. 

Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock 

hazards.

• 

Do not burn or incinerate battery packs –

 Battery packs 

may explode, causing personal injury or damage. Toxic 

fumes and materials are created when battery packs are 

burned.

• 

Do not crush, drop or damage battery packs – 

Do not 

use the battery pack or charger if they have sustained a 

sharp blow, been dropped, run over or have been damaged 

in any way (i.e. pierced with a nail, hit with a hammer, 

stepped on, etc.).

• 

Do not disassemble – 

Incorrect reassembly may pose 

a serious risk of electric shock, fire or exposure to toxic 

battery chemicals. If the battery or charger are damaged, 

contact an authorized Snow Joe

®

 + Sun Joe

®

 dealer or 

call the Snow Joe

®

 + Sun Joe

®

 customer service center at 

1-866-SNOWJOE (1-866-766-9563) for assistance.

• 

Battery chemicals cause serious burns – 

Never let a 

damaged battery pack contact the skin, eyes or mouth. 

If a damaged battery pack leaks battery chemicals, use 

rubber or neoprene gloves to safely dispose of it. If skin 

is exposed to battery fluids, wash the affected area with 

soap and water and rinse with vinegar. If eyes are exposed 

to battery chemicals, immediately flush with water for 20 

minutes and seek medical attention. Remove and dispose 

of contaminated clothing.

• 

Do not short circuit – 

A battery pack will short circuit if 

a metal object makes a connection between the positive 

and negative contacts on the battery pack. Do not place a 

battery pack near anything that may cause a short circuit, 

such as paper clips, coins, keys, screws, nails and other 

metallic objects. A short-circuited battery pack poses a risk 

of fire and severe personal injury.

• 

Store your battery packs and charger in a cool, dry 

place – 

Do not store the battery packs or charger where 

temperatures may exceed 104ºF (40ºC), such as in direct 

sunlight or inside a vehicle or metal building during the 

summer.

Summary of Contents for iON8024-XRP-RM



























Reviews: