background image

9

NOTE: If the charge level button does not appear to be 

working, place the battery pack on the charger and charge as 

needed.
NOTE:

 Immediately after using the battery packs, the charge 

level button may display a lower charge than it will if checked 

a few minutes later. The battery cells “recover” some of their 

charge after resting.

Charger Operation

m

WARNING!

 Charge only iON+ 24V lithium-ion battery 

packs with their compatible iON+ 24V lithium-ion charger. 

Other types of batteries may cause personal injury and 

damage.

To reduce the risk of electric shock, do not allow water to flow 

into the charger's AC/DC plug.

When to Charge the iON+ 24VBAT 

Lithium-iON Batteries

NOTE: The iON+ 24VBAT lithium-ion battery packs do 

not develop a "memory" when charged after only a partial 

discharge. Therefore, it is not necessary to run down the 

battery pack before inserting the charger plug. 

•  Use the battery indicator lights to determine when to charge 

your iON+ 24VBAT lithium-ion battery packs. 

•  You can "top-off" your battery pack's charge before starting 

a big job or after a long day of use.

Charging the Batteries

1. 

Open the battery compartment cover to expose the 

batteries. Press the push lock buttons on the batteries to 

pull them out of the equipment (Fig. 1).

2.  Check that the mains voltage is the same as that marked 

on the rating plate of the battery charger. Then, insert the 

charger's plug into the electrical wall outlet. When you 

plug in the charger, two green lights will illuminate and 

stay green (Fig. 2).

3.  Place the battery packs into the charger by sliding the 

packs to lock them into position. When you insert the 

batteries into the charger, the two green lights will go 

off, and the red lights will 

illuminate to indicate that the 

batteries are charging (Fig. 3).

4. 

When the charger lights turn green, the batteries are fully 

charged (Fig. 3).

 NOTE: 

A fully discharged pack with an internal 

temperature in the normal range will fully charge in  

1 hr 50 mins

 

(between 32ºF/0ºC and 113ºF/45ºC). 

5.  If th

e light indicators do not come on at all, check that 

the battery packs are fully seated into the bay. Remove 

the battery packs and reinsert. If the problem persists, 

contact an authorized Snow Joe

®

 + Sun Joe

®

 dealer or 

call the Snow Joe

®

 + Sun Joe

®

 customer service center at 

1-866-SNOWJOE (1-866-766-9563) for assistance.

6. 

When charging is complete, remove the batter

ies from the 

charger by pressing the push lock buttons and sliding the 

batteries backward to unlock them from the charger  

(Fig. 4).

Fig. 1

Battery

Battery compartment 

cover

Push lock button

Fig. 2

Charger

green

Power on

Fig. 3

Battery packs

red

Charging

green

Fully 

Charged

Summary of Contents for 24V-X2-20SB





















Reviews: