-
1.4. Bypass Input (red/black wire: w3-7)
This wire is designed for external engine start module or turbo timer. Feed this wire with ground when the external engine start
module or turbo timer is activated and the system will bypass the ignition input and shock sensor until the ground pulse is removed.
1.5. Start Output (pink wire: w3-9)
Press and hold button #4, 3 sec. later the system will send a 1 sec. pulse to activate the external engine start module. Pressing
button #4 for 3 sec. will send the pulse again to deactivate the external engine start module.
1.6. Interior Light Supervision (green/white wire: w3-6)
If connected:
-
The interior light will be turned on for 20 sec. when disarming unless the ignition is turned on.
-
The interior light will be turned on all the time whilst the alarm is sounding.
1.7. Program the Optional Features (default=1 chirp)
Follow the steps below to program the Optional Features:
For example: To program the feature #5 as 15sec.
-
Turn the ignition on then off with the system disarmed.
-
Within 10 sec., press the valet switch 3 times.
-
The system enters the programming mode and the siren and LED will be on for 2 sec. to confirm.
*
To Reset to Factory Default:
Within 10 seconds press button #4 for 3 sec., all the optional features will be reset to the factory default and the siren will
sound for 2 sec. to confirm leaving the programming mode.
-
Within 10 sec., press the valet switch 5 times.
-
1 sec. later the siren will chirp 5 times to confirm.
-
Press button #1 of the remote control 6 times to select 15 sec. and the siren will chirp 6 times to confirm the setting.
-
Press the valet switch again (from 1 to 21) within 10 sec. to select the next feature for programming.
*
The system will leave the programming mode and the siren will sound for 2 sec. to confirm if the ignition is turned off at any time
during programming or if the valet switch or remote control button #1 has not been pressed within 10 sec.
1.8. Optional Programmable Features
No Chirp
Function
Τ
1 Chirp
Τ
2 Chirp
Τ
3 Chirp
Τ
4 Chirp
1
1 chirp
Chirp Confirmation
On Off
2
2 chirp
Door Lock with Passive Arming
Disable Enable
3
3 chirp
Ignition Lock
Disable Ignition Brake
4
4 chirp
Ignition Unlock
Disable Driver
All
5
5 chirp
Door Lock Time(sec.)
1) 0.8
2) 3.6
3) 0.8*2
4) 0.8+15
5) 0.8+40
6) 15
7) 40
6
6 chirp
Door Unlock Time(sec.)
0.8 3.6 0.8*2
7
7 chirp
Door Unlock with Disarming
Driver All
8
8 chirp
Siren/Horn Output
Siren Horn
9
9 chirp
Alarm Condition Cycle Duration
30 sec.
60 sec.
10
10 chirp
Interior Light Delay
Disable
25 sec.
40 sec.
60 sec.
11
11 chirp
Auto. Rearming
Disable Enable
12 12
chirp
Auto. Engine Disable(AED)
Disable Enable
13 13
chirp
Door Open Alerts
Disable
Mode 1
Mode 2
14 14
chirp
Total/Comfort Closure
Disable
15 sec.
30 sec.
40 sec.
15 15
chirp
Disarm with Boot Release
Disable Enable
16 16
chirp
Anti-hijacking Countdown
30sec. 60sec.
17 17
chirp
Activate Anti-hijacking Countdown
Normal
Brake
18 18
chirp
Anti-hijacking by Remotes
Disable Enable
19 19
chirp
Anti-hijacking by IDoor
Disable Enable
20 20
chirp
Override Code
Flash 1
Flash 2~10
21 21
chirp
Hazard lights Output
Normal Pulse
Continuous
Factory Default = 1 Chirp
1.9. Feature #20 Override Code (default=1 flash)
Follow the steps below to program:
-
Turn the ignition on then off with the system disarmed.
-
Within 10 sec., press the valet switch 3 times.
-
The system enters the programming mode and the siren and LED will be on for 2 sec. to confirm.
-
Within 10 seconds press the valet switch 20 times to select feature #20
-
1 sec. later the siren will chirp 20 times to confirm the selection.
-
The LED will start to flash 10 times slowly 2 sec. later.
-
Press button #1 of remotes after the LED has flashed the number of times you want to set the code to; Eg. If you want to
choose 6 as the code then press button #1 once after the LED has flashed 6 times. The LED will turn off and siren sound for 1
sec. to confirm.
-
Press the valet switch within 10 sec., to select the next feature for programming.
