background image

 

IMPORTANT SAFETY INSTRUCTIONS 

 

SAFE HANDLING OF GASOLINE 

(Continued From Previous Page) 
3.  DO NOT remove fuel cap or add fuel with the 

engine running. Allow the engine to cool before 
refueling. 

4.  DO NOT refuel the machine indoors. 
5.  DO NOT store the machine or fuel container 

inside where there is an open flame, spark or 
pilot light such as on a water heater or other 
appliances. 

6.  DO NOT fill fuel containers inside a vehicle or 

on a truck or trailer bed with a plastic liner. 
Always place the containers on the ground 
away from the vehicle before filling. 

7. Remove gas-powered equipment from the 

vehicle or trailer and refuel it on the ground.  If 
this is not possible, then refuel equipment using 
a portable container, rather than a gasoline 
dispenser nozzle. 

8. DO NOT start gas powered equipment in 

enclosed vehicles or trailers. 

9.  Keep the nozzle in contact with the rim of the 

fuel tank or container opening at all times until 
fueling is complete. DO NOT use a nozzle lock-
open device 

10. If fuel is spilled on clothing, change clothing 

immediately. 

11. Never overfill a fuel tank. Replace fuel cap and 

tighten securely. 

 

OPERATION

 

1.   DO NOT put hands or feet near or under rotating 

parts. Keep clear of discharge area while engine 
is running. 

2. 

 STOP engine when crossing gravel drives, 

walks, or roads, and under any conditions 
where thrown objects might be a hazard. 

3.   Mow only in daylight or good artificial light. 
4. 

 DO NOT operate mower while under the 

influence of alcohol or drugs. 

5. 

 After striking a foreign object or if mower 

vibrates abnormally, STOP the engine, 
disconnect and secure spark plug wire. Inspect 
the mower for any damage and repair the 
damage. 

6. 

 DO NOT mow near drop offs, ditches or 

embankments. Operator could lose footing or 
balance. 

7. 

 STAY ALERT for holes and other hidden 

hazards. Tall grass can hide obstacles. Keep 
away from ditches, washouts, culverts, fences 
and protruding objects.  

8.   DO NOT mow on wet grass. Always be sure of 

your footing. Keep a firm hold on the handle 
and walk, never run. Slipping could cause 
injury. 

 
 

OPERATION 

(Continued From Previous Column) 
9.  DO NOT leave the machine with the engine 

running. STOP BLADE and STOP ENGINE 
before leaving the operators position for any 
reason. 

10.  Before cleaning, repairing or inspecting make 

certain engine, blade and all moving parts have 
STOPPED. Disconnect and secure spark plug 
wire away from plug to prevent accidental 
starting. 

11.  STOP engine and wait until the blade comes to 

complete STOP before removing grass bag 
and/or clearing grass. 

12.  DO NOT operate mower without the entire grass 

catcher or guards in place. DO NOT point 
discharge at people, passing cars, windows or 
doors. 

13.  Slow down before turning. 
14.  

Watch out for traffic when near or crossing 
roadways. 

15. 

 

DO NOT operate engine in enclosed areas. 

 

Engine exhaust gases contain carbon 
monoxide, a deadly poison. 

 

MAINTENANCE AND STORAGE 

1.   DO NOT store mower or fuel container inside 

where fumes may reach an open flame, spark or 
pilot light such as in a water heater, furnace, 
clothes dryer or other gas appliance. Allow 
engine to cool before storing machine in an 
enclosure. Store fuel container out of reach of 
children in a well ventilated, unoccupied 
building. 

2.   Keep mower and engine free of grass, leaves or 

excess grease to reduce fire hazard and engine 
overheating. 

3.  When draining fuel tank, drain fuel into an 

approved container outdoors and away from 
open flame. 

4.   Keep all bolts, especially blade bolts, nuts and 

screws properly tight. Check that all cotter pins 
are in proper position. 

5. 

 Always provide adequate ventilation when 

running engine. Engine exhaust gases contain 
carbon monoxide, a deadly poison. 

6. 

 Service engine and make adjustments only 

when engine is stopped. Removed spark plug 
wire from spark plug and secure wire away from 
spark plug to prevent accidental starting. 

7. 

 DO NOT change engine governor speed 

settings or overspeed engine. 

8.   Check grass bag assembly frequently for wear 

or deterioration to avoid thrown objects and 
exposure to moving parts. Replace with new 
bag if loose seams or tears are evident. Replace 
slider or bag adapter if broken or cracked. 

Summary of Contents for WMR216017B

































Reviews: