background image

 

32 

Safety Instructions & Operator’s Manual for 

 

21” STEEL DECK 
WALK BEHIND MOWERS 
“M” MODEL 
SERIES 17 

 
 
 

IMPORTANT 

Snapper products are built using engines that meet or exceed all applicable emissions requirements on 
the date manufactured.  The labels on those engines contain very important emissions information and 
critical safety warnings.  Read, Understand, and Follow all warnings and instructions in this manual, the 
engine manual, and on the machine, engine and attachments.  If you have any questions about your 
Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at 
Snapper, McDonough, GA. 30253.  Phone: (1-800-935-2967). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

COPYRIGHT © 2003 
SNAPPER PRODUCTS INC. 
ALL RIGHTS RESERVED 

 
 

MANUAL No. 7-4349 (Rev.1, 2/3/03) 

 

        WARNING 

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR 
EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER 
REPRODUCTIVE HARM. 

 

       WARNING 

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, 
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER 
REPRODUCTIVE HARM. WASH HANDS AFTER

 

HANDLING.

 

Summary of Contents for WMR216017B

































Reviews: