background image

 

21 

 

 

 

 

 

DECAL IDENTIFICATION 

 
 
 
 
 
 
 
 
 
 
 
 
 
(1) WARNING INSTRUCTIONS. 
 
 
 
 
 
 
 
 
 
 
 
 
(2) WARNING: Do Not operate without entire Grass 
Catcher or Guard in place. 
 
 
 
 
 
 
 
 
(3) PRIME: Use for initial engine starting. Read and 
follow engine operating and maintenance 
instructions. Push bulb to prime engine. 
 
 
 
 
 
 
 
 
(4) SPARK PLUG: Warns of potential electrical shock 
from spark plug while engine is running. 
 
 
 
 
 
 
 
 
 
(5) AIR FILTER: Indicates location of engine air filter. 
To service the filter, read and follow the engine 
operating and maintenance instructions. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(6) THROTTLE CONTROL: Indicates direction to 
increase engine RPM (Hare), decrease engine RPM 
(Tortoise), and direction to choke. 
 
 
 
 
 
 
 
 
 
 
 
 
(7) SPEED SELECTOR: Shows direction of motion 
and the ability to select one of six ground speeds by 
rotating the lever. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

SAFETY ALERT 

SYMBOL. OBSERVE 

AND FOLLOW ALL 

SAFETY 

INSTRUCTIONS. 

READ, UNDERSTAND AND FOLLOW INSTRUCTIONS AND WARNINGS IN OPERATOR’S 
MANUALS, AND ON THE MOWER, ENGINE AND ATTACHMENTS BEFORE OPERATING. 

KEEP CHILDREN 
AND OTHERS OUT 
OF MOWING 
AREA. 

 

Summary of Contents for EMRP217017B


























Reviews: