background image

 

24 

Safety Instructions & Operator’s Manual for 

 

EUROPEAN 
21” STEEL DECK 
WALK BEHIND MOWERS 
SERIES 17 

 
 
 

IMPORTANT 

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the 
date manufactured.  The labels on those engines contain very important emissions information and critical 
safety warnings.  Read, Understand, and Follow all warnings and instructions in this manual, the engine 
manual, and on the machine, engine and attachments.  If you have any questions about your Snapper 
product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, 
McDonough, GA. 30253.  Phone: (1-800-935-2967). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

COPYRIGHT © 2003 
SNAPPER PRODUCTS INC. 
ALL RIGHTS RESERVED 

MANUAL No. 7-5514 (I.R. 3/10/03) 

 

        WARNING 

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR 
EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER 
REPRODUCTIVE HARM. 

 

       WARNING 

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, 
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR 
OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. 

Summary of Contents for EMRP217017B


























Reviews: