background image

 

IMPORTANT SAFETY INSTRUCTIONS 

 

OPERATION

 

1.   DO NOT put hands or feet near or under rotating 

parts. Keep clear of discharge area while engine 
is running. 

2. 

 STOP engine when crossing gravel drives, 

walks, or roads, and under any conditions where 
thrown objects might be a hazard. 

3.   Mow only in daylight or good artificial light. 
4. 

 DO NOT operate mower while under the 

influence of alcohol or drugs. 

5. 

 After striking a foreign object or if mower 

vibrates abnormally, STOP the engine, 
disconnect and secure spark plug wire. Inspect 
the mower for any damage and repair the 
damage. 

6. 

 DO NOT mow near drop offs, ditches or 

embankments. Operator could lose footing or 
balance. 

7.   STAY ALERT for holes and other hidden hazards. 

Tall grass can hide obstacles. Keep away from 
ditches, washouts, culverts, fences and 
protruding objects.  

8.   DO NOT mow on wet grass. Always be sure of 

your footing. Keep a firm hold on the handle and 
walk, never run. Slipping could cause injury. 

9.  DO NOT leave the machine with the engine 

running. STOP BLADE and STOP ENGINE before 
leaving the operators position for any reason. 

10.  

Before cleaning, repairing or inspecting make 
certain engine, blade and all moving parts have 
STOPPED. Disconnect and secure spark plug 
wire away from plug to prevent accidental 
starting. 

11.  STOP engine and wait until the blade comes to 

complete STOP before removing grass bag 
and/or clearing grass. 

12.  DO NOT operate mower without the entire grass 

catcher or guards in place. DO NOT point 
discharge at people, passing cars, windows or 
doors. 

13.  Slow down before turning. 
14.  

Watch out for traffic when near or crossing 
roadways. 

15. 

 

DO NOT operate engine in enclosed areas. 

 

Engine exhaust gases contain carbon monoxide, 
a deadly poison. 

 
 
 
 
 
 
 
 
 
 
 

 

MAINTENANCE AND STORAGE 

1.   DO NOT store mower or fuel container inside 

where fumes may reach an open flame, spark or 
pilot light such as in a water heater, furnace, 
clothes dryer or other gas appliance. Allow 
engine to cool before storing machine in an 
enclosure. Store fuel container out of reach of 
children in a well ventilated, unoccupied 
building. 

2.   Keep mower and engine free of grass, leaves or 

excess grease to reduce fire hazard and engine 
overheating. 

3. 

 When draining fuel tank, drain fuel into an 

approved container outdoors and away from 
open flame. 

4.   Keep all bolts, especially blade bolts, nuts and 

screws properly tight. Check that all cotter pins 
are in proper position. 

5. 

 Always provide adequate ventilation when 

running engine. Engine exhaust gases contain 
carbon monoxide, a deadly poison. 

6.   Service engine and make adjustments only when 

engine is stopped. Removed spark plug wire 
from spark plug and secure wire away from 
spark plug to prevent accidental starting. 

7.   DO NOT change engine governor speed settings 

or overspeed engine. 

8.   Check grass bag assembly frequently for wear or 

deterioration to avoid thrown objects and 
exposure to moving parts. Replace with new bag 
if loose seams or tears are evident. Replace 
slider or bag adapter if broken or cracked. 

9.   Mower blades are sharp and can cut. Wrap the 

blades or wear heavy leather gloves and use 
CAUTION when handling them. 

10.  DO NOT test for spark by grounding spark plug 

next to spark plug hole; spark plug could ignite 
gas exiting engine. 

11. 

 

Have machine serviced by an authorized 
SNAPPER dealer at least once a year and have 
the dealer install any new safety devices. 

12.  Use only genuine SNAPPER replacement parts to 

assure that original standards are maintained. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for EFRP216516BV

























Reviews: