background image

40

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date
manufactured.  The labels on those engines contain very important emissions information and critical safety
warnings.  Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and
on the machine, engine and attachments.  If you have any questions about your Snapper product, contact your
local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253.
Phone: (1-800-935-2967).

WARNING

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, CHEM-
ICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRO-
DUCTIVE HARM. WASH HANDS AFTER HANDLING.

WARNING

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR EMIT
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER REPRODUCTIVE HARM.

!

!

COPYRIGHT © 2005
SNAPPER - A DIVISION OF SIMPLICITY MFG., INC.
ALL RIGHTS RESERVED

MANUAL No. 7100237 (I.R. 7/14/2005)

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date
manufactured.  The labels on those engines contain very important emissions information and critical safety
warnings.  Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and
on the machine, engine and attachments.  If you have any questions about your Snapper product, contact your
local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253.
Phone: (1-800-935-2967).

WARNING

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, CHEM-
ICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRO-
DUCTIVE HARM. WASH HANDS AFTER HANDLING.

COMMERCIAL
MID-MOUNT
ZERO TURNING
HYDRO DRIVE
SERIES 1

!

!

Summary of Contents for CZT19481KWV









































Reviews: