background image

5

Operator 

Safety

!

!

Important Operator Safety Instructions (Continued)

Safe Handling of Gasoline

(Continued From Previous Page)

6. DO NOT fill fuel containers inside a vehicle or on a truck 

or trailer bed with a plastic liner. Always place the contain-

ers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or   

trailer and refuel it on the ground.  If this is not possible, 

then refuel equipment using a portable container, rather 

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehi-

cles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or    

container opening at all times until fueling is complete. DO 

NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing          

immediately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tighten 

securely.

Operation

1. DO NOT put hands or feet near or under rotating parts. 

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or 

roads, and under any conditions where thrown objects 

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of   

alcohol or drugs.

5. After striking a foreign object or if mower vibrates    

abnormally, STOP the engine, disconnect and secure spark 

plug wire. Inspect the mower for any damage and repair the 

damage before starting.

6. DO NOT mow near drop offs, ditches or embankments. 

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall 

grass can hide obstacles. Keep away from ditches, wash-

outs, culverts, fences and protruding objects. 

8. DO NOT mow on wet grass. Always be sure of your    

footing. Keep a firm hold on the handle and walk, never run. 

Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is    

running.

10. DO NOT leave the machine with the engine running. 

STOP BLADE and STOP ENGINE before leaving the opera-

tors position for any reason.

11. Before cleaning, repairing or inspecting make cer-

tain engine, blade and all moving parts have STOPPED. 

Disconnect and secure spark plug wire away from plug to 

prevent accidental starting.

12. STOP engine and wait until the blade comes to com-

plete STOP before removing grass bag and/or clearing 

grass.

Operation

(Continued From Previous Column)

13. DO NOT operate mower without the entire grass 

catcher, or guards in place discharge guard, rear guard or 

other  safety devices in place and working. DO NOT point 

discharge at people, passing cars, windows or doors.

14. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate engine in enclosed areas.  Engine 

exhaust gases contain carbon monoxide, a deadly poison.

18. Only use accessories approved by the manufacturer. 

See manufacturer’s instructions for proper operation and    

installation of accessories.

Maintenance and Storage

1. DO NOT store mower or fuel container inside where 

fumes may reach an open flame, spark or pilot light such as 

in a water heater, furnace, clothes dryer or other gas appli-

ance. Allow engine to cool before storing machine in an 

enclosure. Store fuel container out of reach of children in a 

well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess 

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved    

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws 

properly tight. Check that all cotter pins are in proper     

position.

5. Always provide adequate ventilation when running 

engine. Engine exhaust gases contain carbon monoxide, a 

deadly poison.

6. Service engine and make adjustments only when engine 

is stopped. Removed spark plug wire from spark plug and 

secure wire away from spark plug to prevent accidental  

starting.

7. DO NOT change engine governor speed settings or    

overspeed engine.

8. Check grass bag assembly frequently for wear or dete-

rioration to avoid thrown objects and exposure to moving 

parts. Replace with new bag if loose seams or tears are evi-

dent. Replace slider or bag adapter if broken or cracked.

9. Mower blades are sharp and can cut. Wrap the blades or 

wear heavy leather gloves and use CAUTION when handling 

them.

10. DO NOT test for spark by grounding spark plug next to 

spark plug hole; spark plug could ignite gas exiting engine.

11. Have machine serviced by an authorized SNAPPER   

dealer at least once a year and have the dealer install any 

new safety devices.

12. Use only genuine SNAPPER replacement parts to 

assure that original standards are maintained.

Not 

for  

Reproduction

Summary of Contents for 7800596





























Reviews: