Snapper 400ZB2548 Operator'S Manual Download Page 44 | Manualshive

Page: 44 / 48

background image

ENGINE:

26 Gross HP* Briggs & Stratton

Make

Briggs & Stratton

Model

S/N: 2012925786 & Below: 44P777-0124-G1
S/N: 2012925787 & Above: 44P777-0135-G1

Displacement

44.2 Cu. in (724 cc)

Electrical System

12 volt starter, 16 amp. alternator,

Battery: 340 CCA

Oil Capacity

2.0 US qt.. (1.9 L) w/ filter

27 Gross HP* Briggs & Stratton

Make

Briggs & Stratton

Model

44Q777-0146-G1

Displacement

44.2 Cu. in (724 cc)

Electrical System

12 volt starter, 16 amp. alternator;

Battery: 340 CCA

Oil Capacity

2.0 US qt. (1,9 L) w/ filter

*Power Ratings:

The gross power rating for individual gas engine models

is labeled in accordance with SAE (Society of Automotive Engineers)
code J1940 (Small Engine Power & Torque Rating Procedure), and rating
performance has been obtained and corrected in accordance with SAE
J1995 (Revision 2002-05). Torque values are derived at 3060 RPM;
horsepower values are derived at 3600 RPM. The gross power curves
can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas gross power values
are collected without these attachments. Actual gross engine power will
be higher than net engine power and is affected by, among other things,
ambient operating conditions and engine-to-engine variability. Given the
wide array of products on which engines are placed, the gas engine may
not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not
limited to, the variety of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application limitations, ambient
operating conditions (temperature, humidity, altitude), and engine-to-engine
variability. Due to manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this Series engine.

CHASSIS:

Fuel Tank
400Z Models:

Capacity: 5 Gallons (18,9 L)

500Z Models:

Capacity: 10 Gallons (37,9 L)

Rear Wheels

S/N: 2014509321 & Below: Tire Size: 20 x 8.00 -10
S/N: 2014509322 & Above: Tire Size: 20 x 10.00 - 10

Inflation Pressure: 15 psi (1,03 bar)

Front Wheels

Tire Size: 11 x 4.00 - 5

S/N: 2013129510 & Below: Inflation Pressure: 40 psi (2,76 bar)
S/N: 2013129511 & Above: Inflation Pressure: 25 psi (1,72 bar)

TRANSMISSIONS:

HydroGear ZL-KMEF-3L7C-1KLX (LH)
HydroGear ZL-GMEF-3L7B-1KLX (RH)
Type

ZT3100

Hydraulic Fluid

SAE 20W-50 motor oil

Speeds

Forward: 0-7 MPH (0-11,27 km/h)

@ 3400 rpm

Reverse: 0-5 MPH (0-8.05 km/h)

DIMENSIONS:

Overall Length:

S/N: 2014509321 & Below:

68” (173 cm)

S/N: 2014509322 & Above:

71” (180 cm)

Overall Width
48” Model:

49” (125 cm)

Height:

43” (109 cm)

Weight (apx.):

S/N: 2014509321 & Below:

750 lbs. (340 kg)

S/N: 2014509322 & Above:

770 lbs. (349 kg)

NOTE: Specifications are correct at time of printing and are subject to change without notice.

Specifications

Specifications

42

www.SnapperPro.com

Not

for

Reproduction

«
...
42
43
44
45
46
...
»

Summary of Contents for 400ZB2548

















































Reviews:

No comments

Related manuals for 400ZB2548

Brand: Poulan Pro Pages: 60

Brand: jobmate Pages: 19

Brand: Yard-Man Pages: 8

Brand: Hayter Pages: 40

Brand: Weed Eater Pages: 48

Brand: Roller Derby Pages: 4

67971 - LF 3400

Brand: Jacobsen Pages: 122

Brand: Wards Garden Mark Pages: 16

Brand: FGM Pages: 33

Brand: Gardeo Pages: 128

Mini Mini 1,35 Z 079

Brand: Talex Pages: 41

Brand: Toro Pages: 56

Brand: Honda Pages: 81

Brand: Kubota Pages: 59

CRAFTSMAN 944.604060

Brand: Sears Pages: 56

Brand: Cub Cadet Pages: 52

Brand: Craftsman Pages: 100

Brand: Craftsman Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands