Snapper 400ZB2548 Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 48

background image

Fuel Shut Off Valve

Turning the handle to the desired position determines which
tank will be supplying fuel. With the handle pointing LEFT,
it will draw fuel from the left hand tank. With the handle
pointing RIGHT, it will draw fuel from the right hand fuel
tank. With the handle pointing towards the engine, it will
shut fuel flow to the engine.

12

www.SnapperPro.com

Fuel Tank Cap

To remove the cap, turn counterclockwise.

Fuel Level Gauge

Displays the fuel level in the tank.

Features & Controls

Parking Brake

DISENGAGE

Releases the parking brake.

ENGAGE

Locks the parking brake.

Pull the parking brake lever up to engage the parking
brake. Push the lever down to disengage the parking brake.

NOTE: To start the unit the parking brake must be
engaged.

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower. Pull
UP on the switch to engage, and push DOWN to disengage.

Deck Lift Pedal, Cutting

Height Adjustment Pin & Deck Lift Lock
Lever

These control the cutting height of the mower deck.
Depress the pedal until it locks into the 4-1/2” (11,47 cm)
position. Place the adjustment pin in the desired cutting
height and release the lift lock lever.

Throttle Control

The throttle controls engine speed. Move the throttle
forward to increase engine speed and back to decrease
engine speed. Always operate at FULL throttle.

Choke

Close the choke for cold starting. Open the choke once the
engine starts. A warm engine may not require choking. Pull
the knob UP to close the choke. Push to knob DOWN to
open the choke.

Transmission Oil Fill

This unit is equipped with two transmission oil reservoirs.
The transmission oil reservoirs are located beneath the
operator’s seat and in front of the engine. Transmission
oil is added through the transmission oil reservoirs. It also
serves as extra holding capacity as the transmissions heat
up and the oil expands. See CHECK TRANSMISSION OIL
LEVEL for oil level check and fill procedures.

S/N: 2014509322 & Above:

Not

for

Reproduction

«
...
12
13
14
15
16
...
»

Summary of Contents for 400ZB2548

















































Reviews:

No comments

Related manuals for 400ZB2548

532 43 41-99 Rev. 1

Brand: McCulloch Pages: 72

Brand: MTD Pages: 16

Brand: Viking Pages: 36

Brand: Yard-Man Pages: 12

Brand: Gardeline Pages: 19

Brand: Garland Pages: 160

Brand: elem Pages: 99

Brand: Yard Pro Pages: 108

Brand: New Holland Pages: 52

Brand: Grizzly Pages: 96

Brand: Honda Pages: 21

Brand: Black+Decker Pages: 12

Brand: Baroness Pages: 40

Brand: Toyama Pages: 44

Brand: Toyama Pages: 52

Brand: Weed Eater Pages: 21

Brand: DR Power Pages: 44

Brand: Yardworks Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands