manualshive.com logo in svg

Snap-On POLARTEK YF EEAC333, Manual

Share
Download
Snap-On POLARTEK YF EEAC333 Manual Download Page 23

   

• 23 •

 

 

If the refrigerant is PURE the machine will display the following 
screen for few seconds: 

 

Then the AUTOMATIC PROCEDURE will start, and the following 
screen will be displayed: 

 

 

During the recovery phase, the machine displays the quantity of 
refrigerant recovered.  

Upon completion of recovery, the machine will stop and 
discharge, while automatically displaying the used oil extracted 
from the A/C system during the recovery phase. The oil discharge 
operation lasts 4 minutes.  

 

The machine checks whether or not there is air in the tank and, if 
necessary, purges the non-condensable gas. The machine will 
automatically discharge any non-condensable gas. 

Allowing the machine to fully complete the procedure will 
reduce the risk of return flows, which may cause excessive non-
condensable gas to be recharged into the air conditioning 
system. If any residual refrigerant in the A/C system should 
increase in pressure during this phase, the machine will 
automatically begin recovering the refrigerant.  

Then the machine sounds an alarm while the following screen is 
be displayed: 

 

Close and disconnect HP and LP coupling from A/C system, then 
press ENTER , the following screen will be displayed: 

 

Procedure is now successfully completed. 

Press PRINTER to print the receipt of the procedure. Press ENTER 
to exit. 

 

 

z

FIG. 14  

R1234yf                                               

MANUAL PROCEDURE

 

lb 
psi 
oz 

RECOVERY / RECYCLE 

USED OIL DISCHARGE 

Recovered gas 
Tank Pressure 
A/C pressure 
Tank temperature 

 

REFRIGERANT PURITY 

 

 R1234yf: 

 yyy 

% 

 

R134a: 

 

    x % 

 

R22: 

 

    x % 

 

Hydrocarb.: 

    x % 

 

Air: 

 

 x.x % 

 

R1234yf                                               

MANUAL PROCEDURE

 

RECOVERY / RECYCLE 

  R1234yf                                              

MANUAL PROCEDURE

 

 

RECOVERY / RECYCLE 

 

End Of Procedure 

 
 

Gas recovered       xxx lb 
Oil recovered        xxx oz 

 

Press ENTER to continue 

 
 

 R1234yf                                              

MANUAL PROCEDURE

 

 

RECOVERY / RECYCLE 

Close and disconnect HP and LP coupling from A/C 
system and Press ENTER 

 

GAS EXTRACTION FROM A/C SYSTEM 1

st

 PHASE 

Recovered gas 
Tank Pressure 
A/C pressure 
Tank temperature 

 

R1234yf                                               

MANUAL PROCEDURE

 

RECOVERY / RECYCLE 

lb 
psi 
psi 
°F 

Summary of Contents for POLARTEK YF EEAC333

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands