Snap-On 870599 Instruction Manual Download Page 43

Page: 43 / 44

ALLTRADE TOOLS, LLC.

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

CALIFORNIA EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Alltrade Tools, LLC are pleased to explain

the evaporative emission control system's warranty on your 2009 pressure washer.

In California, new equipment that use small off-road engines must be designed,

built, and equipped to meet the State's stringent anti-smog standards. Alltrade must

warrant the evaporative emission control system on your pressure washer for the

period listed below provided there has been no abuse, neglect or improper mainte-

nance of your equipment.

Your evaporative emission control system may include parts such as: carburetors,

fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, con-

nectors, and other associated components.

MANUFACTURER'S WARRANTY COVERAGE

This evaporative emission control system is warranted for two years. If any evapo-

rative emission-related part on your equipment is defective, the part will be repaired

or replaced by Alltrade.

OWNER'S WARRANTY RESPONSIBILITIES

As the pressure washer owner, you are responsible for the performance of the

required maintenance listed in your owner's manual. Alltrade recommends that you

retain all receipts covering maintenance on your pressure washer, but Alltrade can-

not deny warranty solely for lack of receipts.

As the pressure washer owner, you should however be aware that Alltrade may deny

you warranty coverage if your pressure washer or any part of the pressure washer

has failed due to abuse, neglect, or improper maintenance or unapproved modifica-

tions.

You are responsible for presenting your pressure washer to an authorized Alltrade

Service Center as soon as a problem occurs. The warranty repairs should be com-

pleted in a reasonable amount of time, not to exceed 30 days. If you have any ques-

tions regarding your warranty, rights or responsibilities, please contact Alltrade

Customer Service at 1-888-278-8092.

Summary of Contents for 870599













































Search results

Summary of Contents for 870599

Reviews:

Related manuals for 870599

Brands by name

Popular brands

Snap-On 870599, Instruction Manual

Search results

Summary of Contents for 870599

Reviews:

Related manuals for 870599

Brands by name

Popular brands