background image

G. Throughout the ECS Warranty Period, Alltrade shall maintain a supply of warrant-

ed emission-related parts sufficient to meet the expected demand for such parts.

H. Any Alltrade authorized and approved emission-related replacement parts may

be used in the performance of any ECS warranty maintenance or repairs and will

be provided without charge to the purchaser/owner. Such use shall not reduce

Alltrade ECS Warranty obligations.

I. Unapproved, add-on, modified and/or counterfeit parts may not be used to modi-

fy or repair an Alltrade engine. Such use voids this ECS Warranty and shall be suf-

ficient grounds for disallowing an ECS Warranty claim. Alltrade shall not be held

liable hereunder for failures of any warranted parts of Alltrade equipment caused

by the use of such an unapproved, add-on, modified and/or counterfeit part.

EMISSION RELATED PARTS MAY INCLUDE THE FOLLOWING (IF INCLUDED ON

THIS ENGINE):

1. Fuel Metering System

a. Carburetor and internal parts

b. Fuel Regulator

2. Air Induction System

a. Intake manifold

b. Air filter

3. Ignition System

a. Spark plugs

b. Magneto ignition system

4. Air Injection System

a. Air cleaner

5. Exhaust System

a. Catalyst

b. Exhaust Manifold

6. Miscellaneous Items

a. Fittings, tubing, connectors and assemblies. 

TO OBTAIN WARRANTY SERVICE:

If you have any questions regarding this warranty or if your equipment requires a

covered repair, please contact us at the address below.

ALLTRADE TOOLS, LLC.

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

40

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS warranty) for equipment using small

spark-ignited engines:

1. Applicability: This warranty shall apply to equipment that uses small spark-ignit-

ed engines. The ECS Warranty period shall begin on the date the new equipment

is purchased by/delivered to its original, end-use purchaser/owner and shall con-

tinue for 24 consecutive months thereafter.

2. General Emissions Warranty Coverage: Alltrade warrants to the original, end-use

purchaser/owner of the new engine or equipment and to each subsequent pur-

chaser/owner that the ECS when installed was designed, built and equipped so

as to conform with all applicable regulations and was free from defects in mate-

rials and workmanship which could cause the failure of a warranted part at any

time during the ECS Warranty Period.

A. Any warranted part that is not scheduled for replacement as required mainte-

nance in the Owner's Manual shall be warranted for the ECS Warranty Period. If

any such part fails during the ECS Warranty Period, it shall be repaired or

replaced by Alltrade according to subsection (D) below. Any such part repaired

or replaced under the ECS Warranty shall be warranted for the remainder of the

ECS Warranty Period.

B. Any warranted part that is scheduled only for regular inspection as specified in

the Owner's Manual shall be warranted for the ECS Warranty Period. A statement

in the Owner's Manual to the effect of ”repair or replace as necessary” shall not

reduce the ECS Warranty Period. Any such part repaired or replaced under the

ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.

C. Any warranted part that is scheduled for replacement as required maintenance in

the Owner's Manual shall be warranted for the period of time prior to the first

scheduled replacement point for that part. If the part fails prior to the first sched-

uled replacement, the part shall be repaired or replaced by Alltrade according to

subsection (D) below. Any such emissions-related part repaired or replaced

under ECS warranty shall be warranted for the remainder of the period prior to

the first scheduled replacement of that part.

D. Repair or replacement of any warranted emissions-related part under this ECS

Warranty shall be performed at no charge to the owner at an Alltrade Authorized

Warranty Repair Service Center.

E. Notwithstanding the provisions of subsection (D) above, warranty services or

repairs must be provided at Alltrade Authorized Service Center.

F. When the engine is inspected by an Alltrade Authorized Service Center, the pur-

chaser/owner shall not be held responsible for diagnostic costs if the repair is

deemed warrantable.

39

Summary of Contents for 870591






















Reviews: