background image

www.smoothfitness.com

 

 

 

POWER REQUIREMENTS 

 

Power Requirements

 
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC 
SHOCK.  CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE 
PRODUCT IS PROPERLY GROUNDED.  DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT 
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. 
 
This Elliptical can be seriously damaged by sudden voltage changes in your home’s electrical power.  Voltage spikes, surges and 
noise interference can result from weather conditions or from other appliances being turned on or off.  To reduce the possibility of 
Elliptical damage, always use a surge protector (not included) with your Elliptical. 

 
Surge protectors can be purchased at most hardware stores.  The manufacturer recommends a single outlet surge protector with a 
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an 
electrical rating 120VAC, 15 amps. 
 
This Elliptical must be grounded to reduce the risk of electrical shock.  Grounding provides a path of least resistance for electric 
current, should the Elliptical malfunction.  This Elliptical is equipped with an electrical cord that has an equipment-grounding 
conductor and a grounding plug.  Always plug the power cord into a surge protector, and plug the surge protector into an 
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. 
 
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing 
below.  
GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI 
Circuit Breakers may cause this equipment to function improperly. 

 
 
 
 
 
 

 

Summary of Contents for SMOOTH CE-9.0 ELLIPTICAL
















































Reviews: