manualshive.com logo in svg

smith&nephew ZUK, Surgical Techniques

Share
Download
smith&nephew ZUK Surgical Techniques Download Page 40

38

Fig. 28

Fig. 29

Fig. 27

3. Insert the Femoral Drill w/Stop into 

the anterior post hole, and orient it 
to the proper angle (Fig. 27). Do not 
attempt to insert or align the drill bit 
while the drill is in motion. When  
the proper alignment is achieved, 
drill the anterior post hole and, if 
necessary, insert a Femoral Holding 
Peg for additional stability. 

4. Drill the posterior post hole in the 

same manner. This hole is angled  
the same as the anterior post hole  
(Fig. 28).

5. Remove the anterior Femoral  

Holding Peg and cut the posterior 
chamfer through the cutting slot  
in the guide. If a screw/pin was 
inserted into a middle hole, either 
remove the screw/pin or cut around  
it. The remaining island of bone can 
then be resected after removing the 
Femoral Sizer/Finishing Guide. If 
posterior screws/pins were used,  
cut until the saw blade almost  
contacts the screws/pins (Fig. 29).

Summary of Contents for ZUK

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands