background image

Contents 

 

 

27 

 
 

1

 

INSTRUCTIONS FOR SAFETY AND USE __________________________ 28

 

2

 

SAFETY PRECAUTIONS _______________________________________ 30

 

3

 

ENVIRONMENTAL RESPONSIBILITY _____________________________ 32

 

4

 

POSITIONING OF THE HOB  ____________________________________ 33

 

5

 

ELECTRICAL CONNECTION ____________________________________ 35

 

6

 

GAS CONNECTION ___________________________________________ 36

 

7

 

ADAPTATION TO DIFFERENT TYPES OF GAS _____________________ 38

 

8

 

FINAL OPERATIONS  __________________________________________ 42

 

9

 

USING THE HOB ______________________________________________  45

 

10

 

CLEANING AND MAINTENANCE _________________________________ 48

 

 

 
 
 
 
 
 
 
 
 
 

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES 
WHOSE IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS 

MANUAL. 

 
 

 

INSTRUCTIONS FOR THE INSTALLER: these are for the 

qualified 

technician 

who must carry out a suitable check of the gas system, install 

the appliance, set it functioning and carry out an inspection test. 

 

   

 

INSTRUCTIONS FOR THE USER: these contain user advice, 
description of the commands and the correct procedures for cleaning 
and maintenance of the appliance. 

 

Summary of Contents for SR64S
























Reviews: