background image

 

Instructions for the installer

 

 

24 

 

 

2

 

POSITIONING OF THE HOB 

 

  

 

 

The following operation requires building and/or carpentry work so 
must be carried out by a competent tradesman. 
Installation can be carried out on various materials such as masonry, 
metal, solid wood or plastic laminated wood as long as they are heat 
resistant (T 90°C). 
Never use silicone or other insulating products when installing the 
appliance; use only the rubber gasket provided. 

 

 

2.1

 

Attachment to support structure 

 

 Create an opening with the dimensions 

shown in the figure in the top surface 
of the counter, keeping a minimum 
distance of 

50 mm

 from the rear 

border. 
This device is classified "type Y" as 
regards risks against fire and it can be 
set adjacent to walls that are higher 
than the work surface, provided that a 
distance of 

145 mm

. is respected (as 

shown in the figure) to prevent damage 
due to overheating..  

 

 Make sure there is a minimum of 

750 mm

 between the hot plate flames 

and any shelf that may be installed directly above them. Accurately 
position the gasket provided all around the outer edge of the hole in the 
top surface as shown in the figures below, pressing it down so as to 
make it adhere properly. Refer to the dimensions shown in the 
diagram, bearing in mind that the sides A must be flush with the hole.  
Fix the hob to the unit using the brackets B provided. 

 

Carefully trim any excess from border 

of the gasket. The distances in 

the following drawing refer to the hole 

on the inner side 

of the gasket. 

 

 

 

 

 

 

 

Summary of Contents for SNL574GH


















Reviews: