Smeg SNL96XG Instructions For Installation And Use Manual Download Page 1

Page: 1 / 14

Contents

INSTRUCTIONS FOR SAFE AND PROPER USE _______________19

INSTALLATION OF THE APPLIANCE ________________________21

ADAPTING TO DIFFERENT TYPES OF GAS __________________25

FINAL OPERATIONS______________________________________28

USE OF THE COOKING HOB _______________________________29

CLEANING AND MAINTENANCE ____________________________31

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE
IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified
technician who must carry out a suitable check of the gas system,
install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS

FOR

THE

USER:

these

contain

user

advice,

description of the commands and the correct procedures for cleaning
and maintenance of the appliance.

Summary of Contents for SNL96XG















Search results

Summary of Contents for SNL96XG

Reviews:

Related manuals for SNL96XG

Brands by name

Popular brands

Smeg SNL96XG, Instructions For Installation And Use Manual

Search results

Summary of Contents for SNL96XG

Reviews:

Related manuals for SNL96XG

Brands by name

Popular brands