Smeg SHW800B Instruction Manual Download Page 9

 

 

 

 

 

EN 

9

 

USE

 

Control panel 

B

A

D

C

E

G

F

I

H

L

 

 

Button Function 

Display 

Door Closed: Press and hold for approximately 2 Sec-
onds to open the door and turn the motor on at the last 
speed set. 
Door Open: Press briefly to turn the motor Off or On. 

Displays the set speed. 

Decrease the working speed. 

The number of lighted segments decreases. 

Increase the working speed. 

The number of lighted segments increases. 

Can only be activated with Door Open. This speed is 
timed to run for 10 minutes. At the end of this time the 
system will automatically return to the speed set before. 
Suitable to deal with maximum levels of cooking fumes. 

The indicator 

I

 flashes and all the segments 

on the Display are lit. 
 
It is disabled by pressing the Button. 

Can only be activated with Door Open. Starts the Motor 
at a speed that allows suction of 100 m3/h. Cannot be 
activated if Intensive or Delay are active.  

Displays 

24

 and the segments on the Display 

all light up and then turn off one at a time in 
cycle. 
It is disabled by pressing the Button. 

Can be activated with motor on (except for intensive and 
24 mode). Activates automatic shutdown of the Motor 
and the Lighting with a 30’ delay.  

Displays a flashing 

Clock

 symbol. 

 
It is disabled by pressing the Button. 

Performs a 

Reset

 of the Filter saturation alarm when the 

button is pressed for approximately 3 seconds when all 
the users (motor + lights) are turned off. 

After 100 hours in operation the 

Drop

 sym-

bol is displayed to indicate saturation of the 
Metal Grease Filters. 
After 200 hours in operation the letter 

C

 is 

displayed to indicate saturation of the Acti-
vated Charcoal filters.  

Modifies the intensity of the Lighting each time the 
Button is pressed, in cycle. 

 

Door Closed:  

When pressed and held for approximately 2 seconds 
opens the door half way and turns the lighting on to 
maximum intensity. The intensity can be modified using 
button 

H

- When the button is pressed again, the lighting turns off 

and the door closes. 

- Press 

for door fully open, motor at speed three and 

lighting on. 

- When button 

A

 is pressed the lights turn on and the 

motor operates at the first two speeds only. 

Door Open: Press briefly to turn the lighting On or Off. 

 

Door Closed: Press and hold for approximately 2 Sec-
onds to open the door, turn the motor on at speed three 
and turn the lighting on at maximum intensity. 
Door Open: When pressed and held for approximately 2 
seconds turns off the motor and the lighting, cancelling 
any function that may be active and closing the door. 

 

Keyboard Lock: it is possible to lock the keyboard, for example when cleaning the Glass, when the Hood has Motor and 
Lights turned off and when no alarms have been triggered.

 

Press 

F

 (Delay) for approximately 5 Seconds to enable or disable the Keyboard Lock, which is always confirmed by a 

Beep and an animation on the display motor bar.

 

 

Summary of Contents for SHW800B

















Reviews: