background image

Introduction 

 

 

 

 

THE  IDENTIFICATION  PLATE,  WITH  TECHNICAL  DATA,  SERIAL  NUMBER 

AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. 

THE PLATE ON THE CASING MUST NOT BE REMOVED.

 

BEFORE  CONNECTING  THE  DEVICE,  MAKE  SURE  THAT  IT  HAS  BEEN 

REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE 

LABEL UNDER THE CASING. 

 

 

 

 

 

DO NOT PUT

 PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS 

ON THE COOKING HOB GRIDS. 

 

 

 

DO  NOT  USE

  RECIPIENTS  OR  GRIDDLE  PLATES  THAT  EXTEND  BEYOND 

THE EXTERNAL PERIMETER OF THE HOB. 

 

 

 

 

WHERE  THIS  APPLIANCE  IS  INSTALLED  IN  MARINE  CRAFT  OR  IN 

CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER. 

 

 

 

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT 

IS IN OPERATION. 

 

 

 

THE HOB IS TO BE USED BY ADULTS ONLY

. DO NOT LET UNSUPERVISED 

CHILDREN PLAY WITH THE HOB. 

 

 

REPLACED  APPLIANCES  MUST  BE  TAKEN  TO  A  SPECIAL  GARBAGE 

COLLECTION CENTRE. 

 

 

 

The  manufacturer  declines  all  responsibility 

for  damage  to  persons 

or  things  caused  by  non-observance  of  the  above  prescriptions  or  by 

interference with any part of the appliance or by the use of non-original 

spares. 

 

Summary of Contents for PV631CNXAU





















Reviews: