Smeg K43X Instruction Booklet Download Page 16

16

 

 

 

 Intensive speed button. Lights up when the motor is running at speed 4*. 

 Light on / off button. Illuminated when on. 

(*) 

Intensive function

: The motor switches from speed 4 to speed 3 after about 7 minutes. 

During the time in which the intensive function is active, the button flashes and the timer 
function is not activated. 

 , 

 , 

  Pressing these buttons twice activates the timer. The timer function can only 

be activated when the fan motor is on. Once activated, a 10-minute timer starts, when the 
time elapses, the motor stops and the light switches off. The button flashes during this time. 
The timer can be cancelled by touching the same button. 

10.6 Light brightness adjustment function: 

A brief touch of the 

 button immediately switches the light on or off. Touching and holding this 

button for more than 1 second gradually increases the brightness to the maximum level and then 
decreases it to the minimum level as long as the button is pressed. Release the button once you 
have  obtained  the  required  brightness.  This  level  of  brightness  will  be  saved  in  the  non-volatile 
memory so that it will be set each time the light is switched on by tapping the button once. Tapping 
the light button twice when the light is off will set it to maximum brightness. The factory setting is 
for maximum brightness. 

10.7 Reset filter cleaning 

After 100 hours of hood operation, buttons 

 , 

 and 

 will start to flash to remind you to 

clean the filter.  To reset this warning, press the ON / OFF button for 5 seconds, the light of the ON 
/ OFF button will flash once to indicate that the filter time has been reset. 

10.8 24h Clean Air Function 

The 24h Clean Air function allows you to clean the air in the room. To start the 24h function, press 

and  hold  the 

  button  for  3  seconds.  The  extraction  hood  will  run  at  minimum  speed  for  10 

minutes every hour (up to a maximum of 24 hours). The 

 and 

 buttons will flash as long as 

the  function  is  active.  Briefly  touching  any  button  (apart  from  the 

  button)  will  disable  the 

function. 

 

 

Instructions for the user 

EN 

Summary of Contents for K43X





















Reviews: