Smeg Glass Ceramic Induction Hob SE2642ID2 Instructions For Fitting And Use Download Page 12

28

Cleaning and Care

GB

Cleaning and Care

  

• Before cleaning, switch off the hob and let it cool down.
• Never clean the glass ceramic hob with a steam cleaner or

similar appliance!

• When cleaning make sure that you only wipe lightly over the

on/off button

. The hob may otherwise be accidentally

switched on!

Glass ceramic hob

Important!

 Never use aggressive cleaning agents such as rough

scouring agents, abrasive saucepan cleaners, rust and stain
removers etc.

Cleaning after use
1. 

Always clean the entire hob when it has become soiled. It is

recommended that you do so every time the hob is used. Use a
damp cloth and a little washing up liquid for cleaning. Then dry
the hob with a clean dry cloth to ensure that there is no detergent
left on the surface of the hob. 

Weekly clean
2.

 Clean the entire hob thoroughly once a week with commercial

glass ceramic cleaning agents.
Please follow the manufacturer's instructions carefully.
When applied, the cleaning agent will coat the hob in a protective
film which is resistant to water and dirt. All dirt remains on the film
and can be removed easily. Then rub the hob dry with a clean
cloth. Make sure that no cleaning agent remains on the surface
of the hob since this will react aggressively when the hob is
heated up and will change the surface. 

Specific soiling

Heavy soiling

 and stains (limescaling and shiny, mother-of-

pearl-type stains) can best be removed when the hob is still
slightly warm. Use commercial cleaning agents to clean the hob.
Proceed as outlined under Item 2.

First soak food which has boiled over

 with a wet cloth and

then remove remaining soiling with a special glass scraper for
glass ceramic hobs. Then clean the hob again as described
under Item 2.

Burnt sugar

 and melted plastic must be removed immediately,

when they are still hot, with a glass scraper. Then clean the hob
again as described under Item 2.

Grains of sand

 which may get onto the hob when you peel pota-

toes or clean lettuce may scratch the surface of the hob when
you move pots around. Make sure that no grains of sand are left
on the hob.

Changes in the colour 

of the hob will not affect the function and

the stability of the glass ceramic material. These colour changes
are not changes in the material but food residues which were not
removed and which have burnt into the surface.

Shiny spots

 result when the base of the cookware rubs on the

surface of the hob, particularly when cookware with an aluminium
base or unsuitable cleaning agents are used. They are difficult to
remove with standard cleaning agents. You may need to repeat
the cleaning process several times. In time, the decoration will
wear off and dark stains will appear as a result of using aggres-
sive cleaning agents and faulty pan bottoms.

Summary of Contents for Glass Ceramic Induction Hob SE2642ID2


















Reviews: