Smeg CMS4104N, Instruction Manual

Page: 18 / 32

18
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A21) is not blocked. If necessary, remove coffee
deposits with the brush (C5) supplied.
Cleaning the infuser
The infuser must be cleaned at least once a month.
Important!
The infuser (A5) must not be removed
when the appliance is on. Do not use force to remove the infuser.
1. Make sure the machine is correctly turned off (see "Turning
off").
2. Open the service door.
3. Remove the drip tray and waste coffee container (fig. 27).
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 32).
Important! Do not use washing up liquid to clean the
infuser to avoid removing the lubricant applied to the inside of
the piston.
5. Soak the infuser in water for about 5 minutes, then rinse.
6. After cleaning, replace the infuser (A5) by sliding it onto the
internal support and pin at the bottom, then push the PUSH
symbol fully in until it clicks into place (fig. 33).
Please note carefully: If you encounter difficulty in-
serting the infuser, (before inserting it) you must adapt it to the
right dimension by pressing it forcefully from the bottom and
top as shown in the figure 34.
7. Once inserted, make sure the two coloured release buttons
have snapped out (fig. 35).
8. Replace the drip tray and waste coffee container.
9. Close the service door.
Cleaning the milk container (D)
Clean the milk container after each time you prepare milk, as
described below:
1. Lift and remove the lid (D2);
2. Extract the milk container (D3) from the thermal casing
(D6), holding it by the two side grips.
Important!
The thermal casing must not be filled or immersed in wa-
ter: to clean it wipe with a damp cloth.
3. Remove the milk spout (D5) and intake tube (D4).
4. Turn the froth adjustment dial clockwise to the "INSERT"
position (fig. 36) and pull off.
5. Wash all the components of the frother thoroughly with
hot water and mild washing-up liquid. All components and
the container are dishwasher safe, placing them in the top
basket of the dishwasher.
Pay particular attention to check in the hollow and groove
under the dial (fig. 37) that no milk residues remain: scrape
any residue from the groove with a toothpick.
6. Rinse inside the froth adjustment dial seat (fig. 38) and the
milk frother connector hole using running water.
7. Check as well that the intake tube and spout are not
clogged with milk residues.
8. Replace the dial, lining up the arrow with the word INSERT,
the spout and milk intake tube.
9. Place the milk container in the thermal casing.
10. Place the lid back on the milk container.
Cleaning the hot water/steam connection nozzle
Each time you prepare milk, clean the connection nozzle (A13)
with a sponge to remove milk residues deposited on the seals
(fig. 23).
DESCALING
Important!
• Before use, read the instructions and the labelling on the
de-scaler packaging.
• You should use de-scaler authorised by the manufactur-
er only. Using unsuitable de-scaler and/or performing
de-scaling incorrectly may result in faults not covered by
the manufacturer's guarantee.
De-scale the appliance when the display (B) shows message
DESCALING NEEDED PRESS OK TO START (~45 min)
: to
de-scale immediately, press and follow the instructions
from point 4.
To postpone de-scaling to another time, press
: on the
display the symbol is a reminder that the appliance needs
to be de-scaled (the message will be re-proposed every time the
machine is switched on).
To access the de-scaling menu:
1. Press (B2) to enter the menu;
2. Press
(B10) or (B8) until the display shows
DESCALE;
3. Press to start the de-scaling cycle then follow the in-
structions on the display;
4. REMOVE WATER FILTER (fig. 39):extract the water tank
(A12), remove the water softener filter (C4) (if present) and
empty the water tank. Press
;
5. ADD DESCALER (UP TO LEVEL A) AND WATER (UP TO LEVEL
B) (fig. 40); Pour the de-scaler into the tank up to the level