background image

 

 

 

 

14.

 

GUARANTEE 

 

Your  SME  Model  30/12  precision  turntable  is  guaranteed  against  faulty  material  and 
workmanship.  The  nominal  period  of  the  guarantee  is  twelve  months  but  is  liberally 
interpreted at our discretion subject to the following conditions being observed: 

1.

 

Any matter arising must in the first instance be raised with SME  Limited at the address 
appearing below. 

2.

 

In  no  circumstances  return  the  turntable  or  any  part  thereof  to  SME  Limited  unless  we 
have  requested  you  to  do  so.  Responsibility  will  not  be  accepted  for  any  items  or  costs 
arising if this point is disregarded. 

3.

 

Items returned to our Service Department must be: 

a)

 

Sent strictly in accordance with the packing and routing directions which we      

will provide. 

b)

 

Insurance  should  be  effected  by  the  owner.  SME  Limited  are  unable  to  accept          

liability for any items until they reach the factory safely. 

4.

 

Defective parts will be replaced free of charge. The cost of labour may be charged at the 
discretion of SME Limited. Return transport and insurance costs will be charged. 

5.

 

The guarantee expressly excludes: 

a)

 

Damage by any cause whatever. 

b)

 

Contingent and third party liability. 

c)

 

Personal injury. 

6.

 

No alteration or variation of the guarantee will be recognised by SME Limited. 

7.

 

The guarantee is not transferable. 

 

 

SME Limited  ·  Steyning  ·  Sussex  ·  BN44 3GY  ·  England 

Tel: +44 (0)1903 814321  ·  Fax: +44 (0)1903 814269 

e-mail: 

[email protected]

 

 

 

14 

Summary of Contents for 30/12

















Reviews: