SMC Sierra Monitor FPC-N38, Startup Manual

Page: 4 / 43

Riello ProtoNode Start-up Guide
Page 4 of 43
TABLE OF CONTENTS
1 Certification .......................................................................................................................................... 6
1.1 BTL Mark
– BACnet
®
Testing Laboratory ....................................................................................... 6
1.2 LonMark Certification ...................................................................................................................... 6
2 Introduction .......................................................................................................................................... 7
2.1 ProtoNode Gateway ....................................................................................................................... 7
3 ProtoNode Setup.................................................................................................................................. 8
3.1 Record Identification Data .............................................................................................................. 8
3.2 Point Count Capacity and Registers per Device ............................................................................ 8
3.3 Configuring Device Communications ............................................................................................. 9
3.3.1 Input COM settings on all Devices connected to the ProtoNode .............................................. 9
3.3.2 Set Modbus RTU Node-ID for each Device attached to the ProtoNode ................................... 9
3.4 Selecting the Desired Field Protocol and Enabling Auto-Discovery ............................................. 10
3.4.1 Selecting Desired Field Protocol ............................................................................................. 10
3.4.2 Enabling Auto-Discovery ......................................................................................................... 11
3.5 BMS Network Settings: MAC Address, Device Instance and Baud Rate .................................... 12
3.5.1 BACnet MS/TP (FPC-N38): Setting the MAC Address for BMS Network .............................. 12
3.5.2 BACnet MS/TP (FPC-N38): Setting the Baud Rate for BMS Network .................................... 13
3.5.2.1 Baud Rate DIP Switch Selection ..................................................................................... 13
4 Interfacing ProtoNode to Devices .................................................................................................... 14
4.1 ProtoNode FPC-N38 and FPC-N39 Showing Connection Ports .................................................. 14
4.2 Device Connections to ProtoNode ............................................................................................... 15
4.3 BACnet MS/TP or Metasys N2 (FPC-N38): Wiring Field Port to RS-485 Network ...................... 16
4.4 LonWorks (FPC-N39): Wiring LonWorks Devices to the LonWorks Terminal ............................. 16
4.5 Power-Up ProtoNode.................................................................................................................... 17
4.5.1 Auto-Discovery: After Completion
– Turn Off to Save Configuration ...................................... 18
5 BACnet/IP or Modbus TCP/IP: Change the Protonode IP Address .............................................. 19
5.1 Connect the PC to ProtoNode via the Ethernet Port .................................................................... 19
5.2 BACnet/IP and Modbus TCP/IP: Setting IP Address for Field Network ....................................... 20
6 BACnet MS/TP and BACnet/IP: Setting Node_Offset to Assign Specific Device Instances ..... 22
7 How to Start the Installation Over: Clearing Profiles ..................................................................... 23
8 LonWorks (FPC-N39): Commissioning ProtoNode on a lonworks Network ............................... 24
8.1 Commissioning ProtoNode FPC-N39 on a LonWorks Network ................................................... 24
8.1.1 Instructions to Download XIF File from ProtoNode FPC-N39 Using Browser ........................ 24
9 BACnet Explorer ................................................................................................................................ 26
Appendix A. Troubleshooting .................................................................................................................. 27
Appendix A.1. Lost or Incorrect IP Address ............................................................................................ 27
Appendix A.2. Viewing Diagnostic information ........................................................................................ 28
Appendix A.3. Checking Wiring and Settings .......................................................................................... 29
Appendix A.4. LED Diagnostics for Communications Between ProtoNode and Devices ....................... 30
Appendix A.5. Taking Diagnostic Capture with the FieldServer Toolbox ................................................ 31
Appendix A.6. Updating Firmware ........................................................................................................... 34
Appendix A.7. BACnet: Setting Network_Number for more than one ProtoNode on Subnet ................. 34
Appendix A.8. Securing ProtoNode with Passwords .............................................................................. 35
Appendix B. Vendor Information - Riello ................................................................................................ 36
Appendix B.1. 905 Modbus RTU Mappings to BACnet, Metasys N2 and LonWorks ............................. 36
Appendix C. “A” Bank DIP Switch Settings ........................................................................................... 39
Appendix C.1.
“A” Bank DIP Switch Settings .......................................................................................... 39
Appendix D. Reference ............................................................................................................................. 42
Appendix D.1. Specifications ................................................................................................................... 42
Appendix D.1.1. Compliance with UL Regulations ........................................................................... 42
Appendix E. Limited 2 Year Warranty ..................................................................................................... 43