Copy right© 2015 SMC. All Rights Reserved
na.smc.com
Page 4
I/M SMCDW30-D V2.0
5000954
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2)
l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
"
CAUTION
:
1. To comply with FCC RF exposure compliance
requirements, a separation distance of at least 20 cm must
be maintained between the antenna of this device and all
persons.
2. This Transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter "
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
SMCDW30-Z Door Window Sensor
150200001129A R02
10 Battery Installation
A new sensor comes with a preinstalled battery
(CR2 Lithium Battery, DC 3V) with a quick-pull tab for
easy activation.
1. Find the locking mechanism on the bottom of the
sensor.
2. Push down on the back plate of the sensor and slide
out the plate.
3. Insert the CR2 battery into the sensor, with the
positive (+) end matching the product marking.
4. Replace the sensor back plate.
11 Troubleshooting
If you encounter a problem with the sensor:
• Be sure the product has been installed according to
the recommended guidelines found in this guide.
• If pairing to the system, confirm that the sensor has
been first defaulted, and then confirm that the
device is paired to system.
• Verify that a new battery has been installed properly
(see “Battery Installation”).
• Confirm the low voltage indicator is not lit on the
side sensor.
12 ETL Logo and Standard Information
CONFORMS TO ANSI / UL STD. 634 and 60950-1
CERTIFIED TO ULC SUBJECT C634 and CAN / CSA
STD. C22.2 No. 60950-1
13 Compliances
FCC ID: HED-HWS65051DW
IC: 3857A-HWS65051DW
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user authority to operate the
equipment.
“This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.”
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is needed.
• Consult the dealer or an experienced radio/TV
technician for help.
14 Contact
SMC Networks - North America
20 Mason
Irvine, CA 92618
1-800-SMC-4YOU
24/7 Technical Support
With over 40 years of experience, SMC Networks is a
leading equipment provider in gateway and home
security customer premises equipment for Service
Providers in North America and internationally.
Visit us at: na.smc.com