SMC Networks JMHZ2-16D-X7400B-DTB-N Page 6 Operation Manual Download

Page: 6 / 44

- 5 -

JMHZ2-16D-X7400B-HC10DT

、

HC10-(N/P)

Air gripper 1pc.

Protection cover (Valve side) 1pc.
Protection cover (Switch side) 1pc.

Hexagon socket head cap screw
(M4×10) 4pcs. For mounting the cover.

Parallel pin (6×10mm) 1pc.

or positioning the flange.

Hexagon socket head cap
screw (M6×23) 4pcs.
For mounting the product.

Coil tube for piping φ4
(TU0425BU-100) 2m.

Flange for MOTOMAN-HC10 1pc.

* For JMHZ2-16D-X7400B-HC10-(*).

Hexagon socket head cap screw (M4×8) 2pcs.

For fixing INSULOK® tie mount.

INSULOK® tie mount 2pcs.

Flange for MOTOMAN-HC10DT 1pc.

* For JMHZ2-16D-X7400B-HC10DT-(*).

INSULOK® tie 2pcs.

M8-Molex Conversion cable 1pc.

Hexagon socket head cap screw (M6x12)
4pcs. For mounting the flange.

Cross recessed resin round head screw
(M4×6) 2pcs.
For plugging when INSULOK®
cable tie fixtures are not used.

Parallel pin (6×10) 1pc.
For positioning the product.

Summary of Contents for JMHZ2-16D-X7400B-DTB-N













































Search results

Summary of Contents for JMHZ2-16D-X7400B-DTB-N

Reviews:

Related manuals for JMHZ2-16D-X7400B-DTB-N

Brands by name

Popular brands

SMC Networks JMHZ2-16D-X7400B-DTB-N, Operation Manual

Search results

Summary of Contents for JMHZ2-16D-X7400B-DTB-N

Reviews:

Related manuals for JMHZ2-16D-X7400B-DTB-N

Brands by name

Popular brands