Note 4)
Specifications
Fluid that will not corrode stainless steel SUS 630 and 304
12 to 24VDC, Ripple (p-p) 10%or less
55mA or less (With no load)
NPN or PNP 2 output (Max. applied voltage 30V (NPN), Max. load current 80mA)
Variable (0 or above)
Fix (3 digits)
2.5ms or less (With chattering prevention function: 24ms, 192ms, 768ms or less)
With short circuit protection
3 1/2 digit LED display (Sampling frequency: 5 times / sec)
2% F.S.
1 digit or less (Ambient temperature of 25
3
C)
Green LED (OUT1: Light up when ON), Red LED (OUT2: Light up when ON)
No-voltage input (solid state switch or reed switch), 5ms or longer input
IP65
Operating: 0 to 50
C, Stored:
10 to 60
C (With no condensation or freezing)
Operating and stored: 35 to 85% RH (With no)
250VAC for 1 min, between all lead wires and enclosure
2M
Ω
or more (at 50VDC) between all lead wires and enclosure
10 to 500Hz with 1.5mm amplitude or 98m/s
2
, whichever is smaller
980m/s
2
in X, Y, Z directions 3 times each (Not energized)
3%F.S. or less of measured pressure at 25
C in temperature range of 0 to 50
C
Pressure receiving area: Stainless steel SUS 630, Fittings: Stainless steel SUS 304
A2: URJ 1/4 B2: TSJ 1/4
5 wire oil proof heavy duty cable (0.15mm
2
)
Approx. 120g (Each including 3m lead wire)
0.2% F.S.
1 digit or less
0.3% F.S.
1 digit or less
Output voltage: 1 to 5V
5% F.S. or less
Output voltage: 1 to 5V
2.5% F.S. or less
Fluid
Power supply voltage
Current consumption
Switch output
Repeatability
Hysteresis
Response time
Output short circuit protection
Display
Display accuracy
Indication light
Analog output
Auto shift input
kPa
MPa
kgf/cm
2
bar
psi
mmHg
inHg
Hysteresis mode
Window comparator mode
Enclosure
Ambient temperature range
Ambient humidity range
With stand voltage
Insulation resistance
Vibration resistance
Shock resistance
ZSE60F (Compound pressure)
100 to 100kPa
100 to 100kPa
500kPa
0.1
0.001
0.001
0.02
1
0.1
ISE60 (Positive pressure)
0.000 to 1.000MPa
0.100 to 1.000MPa
1.5MPa
0.001
0.01
0.01
0.1
Possible set range
100.0 to 100.0kPa
1.000 to 1.000MPa
Regulating pressure range
100.0 to 100.0kPa
0.1 to 1.000MPa
Note
The possible set ranges for types with auto shift function are as follows:
Function
Various additional functions are available for easy measurement, switch operation and check of measured values suitable for the
conditions of the measured fluid.
Temperature characteristics
Wetted material
Port size
Lead wire
Weight
Note 2)
Note 3)
Note 4)
Note 5)
Auto shift function
Anti-chattering function
Key lock function
Peak hold function
Bottom hold function
Zero out function
Unit conversion function (For overseas use)
Can correct the pressure set point value of switch output according to fluctuation in the primary pressure.
Prevents malfunction due to sudden fluctuations in the primary pressure by adjusting the response time.
The key board operation can be locked to prevent incorrect operation on the operation switch.
Can retain the maximum pressure value displayed during measurement.
Can retain the minimum pressure value displayed during measurement.
The pressure display can be set at zero when the pressure is open to the atmosphere.
Can convert the display value (For overseas use only).
Page 5
Page 16
Note 1) Select and order by specifying the types and models.
Note 1) In case of types with unit conversion function. (Types without unit
conversion function are fixed to the SI units (KPa or MPa).)
When a type with analog output is selected.
When a type with auto shift is selected.
0.03 to 0.04 psi in psi display.
Value clear
0.01psi in psi display.
Rated pressure range
Operating pressure range and regulating pressure range
Proof pressure
Setting/Display
resolution
Environment
resistance
Note 1)
Note 2)
Note 3)
Note 1)
Note 1)
10
Approved
For General Fluids
High Precision Digital Pressure Switch
Series
ZSE60F/ISE60
ZSE/ISE 4/21/02 1:15 PM Page 13
