SMC Networks ISE20CH-L Operation Manual Download Page 89

Page: 89 / 108

-88-

No.PS

※※

-OMX0002

Problem

No.

Problem

Problem possible

causes

Investigation method

Countermeasures

The operation is
unstable.
(chattering)

Effect of line
pressure
fluctuation
because
hysteresis is too
narrow or delay
time of the switch
is too short

(1) Check the set pressure values

(hysteresis)

(2) Check the delay time.

(1) Check the pressure

setting.

(2) Reset the function

settings.

Incorrect wiring
or broken lead
wire

(1) Check the power supply wiring.
(2) Check if there is bending stress

applied to any parts of the lead
wire.

(1) Correct the wiring
(2) Correct the wiring

conditions (reduce the
tensile force and
increase the bending
radius).

Product failure

Replace the product.

Summary of Contents for ISE20CH-L













































































































Search results

Summary of Contents for ISE20CH-L

Reviews:

Related manuals for ISE20CH-L

Brands by name

Popular brands

SMC Networks ISE20CH-L, Operation Manual

Search results

Summary of Contents for ISE20CH-L

Reviews:

Related manuals for ISE20CH-L

Brands by name

Popular brands