manualshive.com logo in svg

SMC Networks EX260-VIL1, Operation Manual, Page: 38 / 41

Share
Download
SMC Networks EX260-VIL1 Operation Manual Download Page 38

-

38- 

 

No.EX

※※

-

OMZ0018

 

 

10. 

Troubleshooting 

 

The following shows the troubleshooting related the SI Unit. 
 

Table 10-1. Troubleshooting related COM LED indication 

No. 

Content 

Probable causes 

Checking methods and measures 

1  COM LED is OFF. 

Power supply for logic/input is low   
(< approx. 16.8 VDC) or not 
present. 

Check the power supply voltage for 
logic/input being supplied to the SI Unit. 
Supply the voltage considering the voltage 
drop on the wiring. 

The communication/power cable 
is broken. 

Check the connection of the 
communication/power cable. 

2 

COM LED is green ON. 
The port LED of the 
IO-Link master is green 
flashing *. 

The communication/power cable 
is broken. 

Check the connection of the 
communication/power cable. 

3 

COM LED is green ON. 
The port LED of the 
IO-Link master is green 
ON *. 

The IO-Link master port is not in 
IO-Link mode. 

Set the IO-Link master port to IO-Link 
mode. 

Process data size of the IO-Link 
master is smaller than the process 
data size of the SI Unit. 

Set the process data size of the IO-Link 
master to be larger than the process data 
size occupied by the SI Unit. 

4 

COM LED is green ON. 
The port LED of the 
IO-Link master is green 
blinking fast *. 

The IO-Link master has detected 
a device matching error. 

Disable the device matching function on 
the IO-Link master or connect an SI Unit 
that matches the DeviceID or 
SerialNumber registered in the IO-Link 
master. 

 

Note

 

 

 

LED indicator status may vary depending upon the IO-Link master in use.   
Check the specification of the IO-Link master for details. 

 

Summary of Contents for EX260-VIL1










































Reviews:

No comments