background image

Model 5100-XX-IT Toxic Gas Sensor Module

 

Page:  32 

APPENDIX C: LIMITED WARRANTY 

SIERRA MONITOR CORPORATION warrants its products to be free from defects in workmanship or material 
under normal use and service for two years after date of shipment.  SMC will repair or replace without charge 
any equipment found to be defective during the warranty period.  Final determination of the nature and 
responsibility for defective or damaged equipment will be made by SMC personnel. 

All warranties hereunder are contingent upon proper use in the application for which the product was intended 
and do not cover products which have been modified or repaired without SMC approval or which have been 
subjected to accident, improper maintenance, installation or application, or on which original  identification 
marks have been removed or altered.  This Limited Warranty also will not apply to interconnecting cables or 
wires, consumables (ie. calibration gases, batteries, sensors), nor to any damage resulting from battery 
leakage. 

In all cases SMC’s responsibility and liability under this warranty shall be limited to the cost of the equipment.  
The purchaser must obtain shipping instructions for the prepaid return of any item under this warranty 
provision and compliance with such instruction shall be a condition of this warranty. 

Except for the express warranty stated above, SMC disclaims all warranties with regard to the products sold 
hereunder including all implied warranties of merchantability and fitness and the express warranties stated 
herein are in lieu of all obligations or liabilities on the part of SMC for damages including, but not limited to, 
consequential damages arising out of/or in connection with the use or performance of the product. 

 

Summary of Contents for 5100 IT Series







































Reviews: