background image

 

 

ROOF  ASSEMBLY CONT... 

12 

STEP 6: 

 

 

Place barge flashings on roof at end of shed ensuring 
the diagonal trimmed end is facing out. 

 

 

Rivet the Barge Flashings to the roof and the side wall, 
using four rivets on top of barge and four into the side 
(

fig.2

).

 

fig.1 

STEP 4: 

 

 

Position the second Roof Sheet, ensuring the slots line up with 

the first sheet. 

 

 

Rivet together as shown. 

 

 

Nail off as per Step 4. 

 

 

Rivet and nail off the remaining Roof Sheets, ensuring the ribs 

line up with the front Roof Sheets and the back Wall Sheets.

 

fig.1 

SIDE 

WALL 

FRONT 

WALL 

BACK 

WALL 

SIDE 

WALL 

TOP PLATE 

BOTTOM PLATE 

RIDGE BEAM 

SIDE

 

WALL

 

FRONT WALL

 

BACK WALL

 

SIDE

 

WALL

 

TOP PLATE 

BOTTOM PLATE 

STEP 3: 

 

 

Position 1 x roof sheet (slotted end facing back) so that the 
top of the sheet is at the centre of the Ridge Beam and the 
side of the sheet over hangs the end of the Ridge Beam and 
the Top Plate by 15mm. 

 

 

Ensure the Ridge Beam and the Top Plate are straight. 

 

 

Nail 4 x corners of the Roof Sheet as shown, ensuring the 
ribs on the Roof Sheet line up with the front Roof Sheet and 
the back Wall Sheet. Nail off the first sheet. 

SIDE

 

WALL

 

FRONT WALL

 

BACK WALL

 

SIDE

 

WALL

 

TOP PLATE 

BOTTOM PLATE 

fig.2 

X 4 

X 4 

Barge

 

STEP 5: 

 

 

Rivet the 2 ridge flashings together using 4 rivets, 
so total flashing is 3.050m long. Rivet the Ridge 
Flashing to the centre of the roof using 8 x rivets 
as shown (

fig.1

). 

STEP 7: 

 

 

Place spouting in position and rivet to Barge Flashings at 
each end and rivet to roof sheets (1 rivet per 1 sheet). 
Repeat with remaining spouting. 

Summary of Contents for SS3025

















Reviews: